6G Celicas Forums

Are these custom made or jdm and how is the quality of the lamps??

Thank you for the help guys I returned the sending unit n got the bracket... I really appreciate ur help!!!

Ok so the dealer wants 155.00 for the sending unit!!! I don't want to spend that much...guys I need ur help anyone know where I can buy it cheaper?? My car is a 94 GT thanks in advance...

thanks i would of thought that the dealership would be expensive like over 100 or something...i will check tomorrow morning thanks again

my fuel pump ssending unit that is on top of the gas tank is rusted and the lines are leaking...and i cant find one for a 1994 anywhere.... i just bought a new fuel pump but the sending unit that bolts to the tank is shot!!! any help is appreciated!! thanks

oh man... you all got some opinions!!! lol the spacers i used are 3/4 inch in the front and 1 inch in the rear...i just got in eibach pro elignment camber bolts today so once i get them in i can drop it down cant wait... the car is different...unique...which is what i like about it... thank for those of you who do like it...alot of work n money to get it here so far and.... for those of you who don't like it... well...who really cares!! its stilll a celica and this is suppose to be a club that supports each others celicas not hatin on it...

35 offset

no...my turn singals are in the hole...also i removed the screen in the very front of the bumper to paint it up and to add alittle something extra to make it stand out abit...but not planning on add any fogs to it.

thanks for your comments both good and bad...lol...honesty is best!! i just ordered Eibach Pro-Aligment Camber kits to get my fenders down near the top of the rim and yeah the gap sucks and its sitting in my garage til i get it sitting right...i just wanted to post some pics of my project to show you where im at with it...i have to still do a few things to the exterior to finish it off...but its a project and its slowly getting there...i will post more pics of it once the camber kits are installed...

these are my pics after i installed them. i am waiting for my camber kits to come in and i still have to adjust my coilovers to drop the car down even lower!! I also have the center caps for the rims too...just didn't have them on when i took the pics...

nintyfourcelicaman... 94-95 clear turns!!!!

hi i just got adapters for a 114.3 n 120 bolt pattern to go onto my 5x100 celica....$179.00 shipped from adaptitusa.com i went with a 20mm up front and a 25mm in the rears with my offset being 35 on the rims...they are 18x 8 1/2 i am going to order camber kits for my car too...just stretched some new tires i got today...Nitto Neo Gen...they are for lowered cambered cars..(to wear evenly) size 205/40 R18...waiting for the adapters to come in any day to install them i will let you know how they fit...

I just did the same on my car did the brake hardware kit and shoes...the drums did NOT want to go back on over the shoes...they were hitting in 2 places...i ended up taping them on with a hammer...and they were tight!! i just drove it until they wore down a bit!!

thank you for the link and the advice!!! i will let you know how i make out with it all.... i really do appriciate it! thanks again

ok...so if i am running 1/2 inch past the stock fender...but i have fiberglass billlit fenders....i wonder if they are wider than stock??? also how do i buy camber kits?? Thanks for all the help and advice so far...i'm trying to figure this all out as we go along!!

I can buy 20mm adapters for the front....that would take me to +15... i think you said above that i need et+27 for the fronts...Hmm...what number do i need to get to? can anyone tell me how i install camber and where i can buy them please? thank you.

ok guys...i found a good deal on some Enkei EV5 18x8 1/2" with a 35 offset, need to see if i need to roll my fenders, spacers or stretch my tires...or camber...? the 19" i feel raised the car too much...so 18s it is!! anyone has this size wheels? any help would be greatly appreciated!! thanks in advanced!

okay so i decided not to go with 19" rims and found a great deal on some 18" x 8 1/2" Enkei EV5 wheels with what i believe is a 35 offset (stamp is on the inside of the hub, a 35 inside a circle)...what will i need for a flush look? will i need spacers and what tires should i get? my car is lowered...THANKS in advanced.

thanks alot they pulled right off that way...i will paint them up tomorrow and have some pics for the finished product!! thanks again for all of the help!!!

does anyone have 19" rims on your car already...if so can you tell me what you have had to do to get them to fit...and if fender roll, spacers, camber kit, and or cutting was needed? Thanks...and pics of 19s would be great!!!! thanks again!

just be sure to keep the can far away...at least 12" and do VERY light coats...wait like 5 minutes and just spray over it again...you don't want any heavy coats on it or any drips!!!! I went really dark on mine and the visibility is still great with it!!! i will take a pic 4 u 2nite k?

thanks guys i thank you for your help!!

I used 3/4 of a can of niteshades and have a glossy finish...the key is to wipe the tail lite down good with rubbing alcohol and don't touch the lense after wiping it to avoid oily finger prints on it! and spray many lite coats and give it time in between to tack up before applying more lite coats!...for $12.00 made a big difference...you can use a gloss clear over it after 12-24 hours of drying...I think it will look good on your red car..

hey everybody... i just bought some rain-X Latitude wiper blades and i want to take off my wiper arms to paint them...they are a little rusted and dull...I'm sure that there is a right way to remove them...can anyone help me?? Thanks in advanced!!!