6G Celicas Forums

I took my celi in for its MOT last weekend and it failed on the fact the ABS doesn't work. As it turns out the not very nice man (who I'd quite like to punch right now) has disconnected the light from the dash so it doesn't show up.

I need to know what the most likely problems are. It locks all four wheels under heavy braking and all the sensors and relays seem to be working and getting power. My mate is doing the repairs at his garage for me but hasn't worked on a 6th gen before

I really need help with this as I can't drive until I get it sorted

So it would be better to plug that hole and fix the o2 sensor to the downpipe?

No its an o2 sensor its on the wright up on here

7afe Header Install

and this is the picture it shows



its taken looking up through the engine bay so that is the one in the manifold

This is the new manifold



And this is the one on the car



The new one has the boss for the lambda sensor and the old one doesn't however there is another sensor on the downpipe further down

can I just swap the sensor locations?

I've got a new header and downpipe for my 7afe but the header has the boss for an O2 sensor my car doesn't have. Is it ok to move the one from the old downpipe to the header?

Need some help its my first car and have no experience with anything other then electrics yet

Bought a new manifold (header) from the States but it has the hole for the O2 sensor and they weren't put on UK cars so I need a sensor or a bung.

Anyone got and old one as its not going to be connected to anything anyway

If its a good day Red Hot Chilli Peppers maybe some rolling stones

If its a bad day slipknot and nine inch nails

The jet itself isnt blocked i've traced the lines back to the engine bay and there is no water in the lines

The pump works fine and so does the switch I can hear the pump working when I flick the switch

Like I said the last guy who owned her didnt look after her very well so its probably just clogged water lines

thanks guys is it a separate pump for the rear? The front works fine and i can hear a pump whirring when i hit the switch just no water. Its probably just a blockage.

The last guy hadn't looked after her that well

Wasn't sure where exactly to put this thread so it's going here.

My rear washer jet isn't working I've traced it back to the engine bay but I don't know how to get to the washer bottle.

I know it's a noob question but it is my first car I've had to work on.

I do know where the bottle is but do I have to get at it from below?

When you say you spliced the harness onto the loom did you have to solder or was it just connector blocks?

An aftermarket audio harness should use your original plugs and adapt them to the standard ISO connection.

If you had to cut and splice it may be you did it wrong.

I'm a professional audio fitter and I see cut & splice everyday that people have done wrong because a connection is dodgy or the splice to the wrong wire

I think the Euro ST must be different to the USDM because my ST has ABS and Discs all round sunroof and a 5 speed manual as well and so has every other Ive seen come to think of it

got mine off with some t-cut

Ok so I picked up a front and rear and they both fit great but i havent got the bolts the connect the front to the bodywork. what size are they? I've tried M8s and they're too small and M10s seem to big but that could be the wrong thread.

would an GT4 rear strut bar fit on an ST?

Removed the celica badge from the back and started removing the old peeling paint so it can be repainted and stuck to the mirror

Already read that one. It's just to make it stay down I needed it to rise only when I want it too. Anyway I got it working after I wired a switch onto the power antenna wire

I need help with the Toyota TVSS III-B system. It didn't work when i bought the car as the guy I bought it off took the battery out of the only fob to change it and left it out too long so its got to be recoded. Any ideas how? I've tried everything i've found online and nothing's worked I really dont want to go be ripped off by toyota for a 5 min job

Any help would be great

Never mind I'd been a spoon one of the wires on the audio harness actually said "power Antenna" on it so I cut it and no antenna. Its the Black/Red on the 96 loom for anyone else who wants to know

Hi guys

which wire powers the antenna to go up and down. I'm installing a switch so it only goes up when im listening to the radio not just ipod, cd etc

Any ideas on the best way to do it? Obviously it has to be at the stereo end not the back by the aerial. I don't want to swap it or make it stay down all the time

fog lights thats what I got on mine

go for the red Im looking to get some red ones aswell