6G Celicas Forums

Front and rear kit, wing and bottom of door off the mr2 molded into the car. The car was never finished and has to go. The project will not be finished. I have a front mount ic that was custom built for the car. No engine or trans included. Only thing inside the car is the dash and shifter.

PRICE:1500

NEED IT GONE ASAP...

Pics will be attached soon.

I need the whole setup from rim tire size and width to tire height and width, mph, 1/4 times.. the car is using a st205 trans

Hello All,

Just as the title states, i'm looking for a rim tire combo that will allow me to run a set of slicks on all 4 and the height be enough for the E153 ruining low 9's high 8's. I have been searching around and found a set of 15's that should clear but i still need to know what worked before and whats best for MPH and overall shorter time.

Thanks,
Eazy

Hello,

I am looking for a low mile clean AC compressor with lines for a Gen 3/4 ST205/215. It must have a 5 rib belt and Celica/Caldina compatible.

Board Name: Eazy2001x
Location: Long Island, NY
Means of Contact: eazy2001x@yahoo.com / PM

Thanks,
Eazy

Yeah

Not my pic but it looks like this..

125 shipped..

145 shipped...

190+ shipping or I can meet you locally if its not too far..

Closed, Sold..

It will have to be shipped in two packages. I can prob get it into one box. Based on all I ever shipped. I figure if I can get ot into one box.. The 100-105 range in the us ground, insured and tracking.

I'm willing to do local pickup of up to 50 miles to save on shipping.

I'm willing to do local pickup of up to 50 miles to save on shipping.

I'm willing to do local pickup of up to 50 miles to save on shipping.

I'm willing to do local pickup of up to 50 miles to save on shipping.

Beams? Yes.. But it will sell with the head.

Description: Up for sale is a Gen 3 3S-GE Vented Valve Cover With -10AN vents. It has two vents, one on the dizzy side and the other is where the PVC use to be, this allows you to vent to a catch can. It was also powder coated in blue. Its dirty and needs to be wiped down, i didn't do this before taking the pics. This costed me much money to have all this done and im willing to let it go for 125+shipping.









Board Name: Eazy2001x
Location: Long Island, NY
Means of Contact: eazy2001x@yahoo.com / PM

I have a Gen 3 3S-GE Oil Pan Set, upper and lower pan and oil cooler with center bolt for sale $165 shipped in the US. the oil cooler is from a Gen 4 3S-GE beams engine with 30k on it and never spun a bearing.

Board Name: Eazy2001x
Location: Long Island, NY
Means of Contact: eazy2001x@yahoo.com / PM

I'll do 150 shipped us price only

Todays special.. 195+ shipping

I have two of these heads now.. One is missing a bucket and doesn't have a valve cover. i have a modded one for sale separate.

Todays special.. 390+ shipping for everything..

275+shipping

475+shipping

Board Name: Eazy2001x
Location: Long Island, NY
Means of Contact: eazy2001x@yahoo.com / PM

Description: Up for sale is a Gen 3 3S-GE head for sale. It will include the head, valve cover, top feed fuel rail and injectors along with stock cams which are larger/more aggressive than the stock Gen 3S-GTE cams. This head can bolt up to the Gen 1/2/3/4 3S non VTI or Gen ? 5S blocks with no problems. Now you have to buy a head, to bolt up and go or build with no down time on your current build until your ready to swap. There is no intake manifold included but most of us have custom intake manifolds anyway so here is a good place to start. Also note that the intake and exhaust manifold ports are exactly the same on the Gen 3 3S GE and GTE heads. However the stock intake manifold wont bolt up because the throttle body wont clear the stock 3S-GE valve cover without modifications. But it can be done with a few cuts and aluminum welds. Price 300 Plus shipping.

Pics:

Board Name: Eazy2001x
Location: Long Island, NY
Means of Contact: eazy2001x@yahoo.com / PM

Description:

I'm cleaning out my garage.. I am never going to move forward with most of the stuff I have and just have way too much stuff. I am selling a complete Red top Rev 4 3S-GE Auto head kit. You will get the head complete with everything that bolts so it including the fuel rail, injectors, intake manifold, ETC? I will also include the ECU, MAF, un-cut celica SS3 wire harness, Coil's and head studs if you want them. I am firm on my price cause im really just letting this thing go at 500 Plus shipping. If your local enough ill even drive to meet you once payment is received.

There are two problems with this setup. The VVT-I solenoid plug pins were broken and needs to be repaired or replaced. The vacuum port where the brake booster line connects to was bent and needs to be straighten and repaired. There is a small hole where the bend was. You should be able to JB weld it and be fine, its really small. See pics below.

Don?t miss out on your once in a lifetime chance to get everything you need to swap this on your turbo or N/A/ If you were ever looking to Borden your usable power output here it is. Everything about this head is much more improved than the Gen 1/2/3/4 3S-G(TE/E) engine heads. This will also clear your strut tower.

For more information please see my threads:

BEAMS 3S-GE Head On A 5S Block (Need Help/Pics/Info!)
http://www.mr2oc.com/showthread.php?t=206777

BEAMS 3S-GE Head On A 5S Block (Need Help/Pics/Info!) - Part 2
http://www.mr2oc.com/showthread.php?t=434742

Built Gen 2 3S-GTE Head On Gen 4 3S-GE 11:1 CR Block With Gen 2 Oil Pump/Pan
http://www.mr2oc.com/showthread.php?t=580873

Pics:









Thanks,
Eazy

I'm in long island ny and need 2 manual engine harnesses and 1 dash harness for a 5sfe. i need these parts for two different cars.. so if you have a dash and engine harness together ill take them both.. if you have just the engine harness ill take that separate. I also have cruse control on the car and its a GT.

PM me or e-mail me eazy2001x@yahoo.com