6G Celicas Forums

Do you still have front caliper n bracket? if so how much shipped to 97233

thanks for offering your help but i actually found someone local that i could interview. but if anything pops up in the next couple days i'll be sure to post it.

Ok, so I'm currently working on a class project right now and I need to "interview" someone from Canada. I just need to get some information about the social and business customs. any help would be much appreciated.

Happened to come across this page when i was bored so i decided to paint a picture lol

the underlined letters is the series of the engine and most parts aren't interchangeable

okay so i'm guessing its been doing this for a while, just that with the music on and what noy i've never noticed it. but when i hold the brake pedal down my lights dim and the idle drops a little to where the car mildly shakes. this happens even when the car is warm. also lights get bright again when i release the pedal any ideas? checked bat when running and its +/-13v. i'm just worried the car will take a dump on me at a light or something.

ok so i'm picking up a 5s but its strapped to a pallet... now where i'm picking it up from they have a fork lift to load it but i'm going to be dropping it off at my place, and here lies the problem. i didn't get the fork lift i've always wanted for x-mas last year, so how would i go about unloading it? would i be able to use a cherry picker to do it?

oh yeah dont know if it matters or not but the trans is still bolted up well thanks in advance

ok so my buddy and i cranked it out and replaced the belt. now it makes a rinding noise when i rev, did i over tighten the belt or is that normal? and when i was doing the timing the notch was slightly to the right of 0 is that retarded or advanced?

i do believe its a non interference engine

ok the rotor is not spinning... so its safe to say that its my timing belt right? i've never done a timing belt before but i found a guide online for the 5s. how long would it take to replace it normally?

its for a mr2 but since it is the same engine i'd figure it would be the same.
i'm going to take a crack at it this weekend. anyone got any tips for me?

http://www.baktasht.com/_html/hosted/timingbelt.html

ok so i was going to my buddies house and the car died while in motion. pulled out the spark plug tester and i'm getting no spark. i'm curious how do you check if the timing belt snapped? also how would i know if it was my dizzy?

ok so i replaced my bumper and fender, but the bumper is gray and the fender is black. and for the time being i would just like to spray a layer of primer so the celi isnt tan black and gray. i was thinking about sanding with 400 to 800 then to like 1200 then spraying it.

2x i never gave it a name but thats what i did. now i use the cup holder to hold my phone. the change holder i use when i'm to lazy to unplug the navi from the car so i just pop the whole thing under the armrest while its still plugged into the cig lighter. also have been meaning to purchase a lighter relocation kit to save my thumb from smashing into it when i shift to first or drop the e-brake

hi bought an mr2 with a hole in the block, and i need a 5s to make it run so my girl can drive it around. lmk if you have an extra motor lying around. preferred if you are from portland

PM'd Pics are up

i have some extra parts

-Driver side regulator and motor *SOLD*
-Passenger side regulator and motor *PENDING*
-driver and pass switches
-driver side tweeter bracket and cover
-a driver side mirror but the wire has been cut
-have 2 door lights

i dont have a set price on these just shoot met an offer

are we able to use the 92 mr2 5s cams on ours? because i have an extra pair.

ok i'm looking at gettin a 3s from a 93 mr2. if i was to pick it up. what would i have to source to get it in that i wouldnt be able to use from the 2? motor mount? custom exhaust? intercooler pipping? how bad would the wiring be?
i just want to get an idea of what my shopping list would be like.

i have a 95 gt and i would still be using the trans

had my leak from the valve cover gasket. it turns out the people who did the tune up didnt tighten it all the way and i could literally loosen it with my fingers

lol i'll settle with "arent too bad" for the bumper i guess, but the fender was toyota oem. so 1 of 2 isnt that bad.
the next step is frame work for me.






never dont frame work so this might take a while. anyone done this before? if so what tools are needed?

ok i ordered a new bumper and a new fender got them together for 280. the fender is oem and cost 155. the bumper was made from Tong Yang Group and was 125. the place i got this from was a local wrecking yard in my area. the salesman told me when i ordered it, that the fender was oem and i assumed that the bumper was to. (mah bad i guess, i should of asked) has anyone had one of these TYG bumpers?

lol i'm having that same problem. i think i'm going to go into a toyo dealership tomorrow and see if i can get some help finding the part. if they have it i'll make sure to make a note of the part number for you.

ok so i need the driver side bracket that holds up the headlights on the from the bottom. i tried looking in 1sttoyotaparts but no luck are there any other places like that?

all the pics i click on show up black. anyone know whats going on?

damn i want one of those key chains all i found when i took my car apart was a gold necklace and 63cents and the seats look great after what you cleaned them

ok i was trying to pull my fender but had no luck. 3 bolts under the hood. 1 in the door jam. 2 on the bottom. and 3 to the bumper. where is the rest of them?