6G Celicas Forums

When Edophus referes to a spherical bearing does he mean this?? :



So the McPherson Control arm has a bushing in place and the superstrut lower control arm has a spherical bearing in the LOWER ARM #1 (the one with 2 ball joints and a spherical bearing), because the lower control arm on the superstrut design moves more due to it being a more well designed suspension like the double wishbone suspension??

yea see the mounting points for mcpherson and look the exact same, but are not see pics below.







This post has been edited by BonzaiCelica: Oct 14, 2014 - 5:09 PM

The bearing on the superstrut lower control arm where it mounts to the body is very different to the mcpherson strut bushing here, on the ss lower control arm once the arm is cast, they machine the end that joins to the body, it forms one half of the spherical bearing, so its actually machined from the control arm, the centre of the bearing is then put into the arm, and the other half of the bearing then pressed in. The bearing isnt a seperate peice and cant be swapped or replaced once its done the arms only fit for the bin. The banana arm bushing you could replace, i beleive some people in the uk have done that.

Those roll centre adjusters look good, It aint going to cure the downsides of mcpherson struts but should help correct the geometry after lowering, that must be mega low to need them though!!

Pointless post

This post has been edited by BonzaiCelica: Oct 11, 2015 - 5:39 PM

I can honestly say from experience that it will not hold for very long, my end links were bent from the pressure and the car was sitting for the most part so I switched them out for the supperstrut setup, the enlinks are longer and the swaybar is positioned diferently

I was speaking words without wisdom here

This post has been edited by BonzaiCelica: Oct 11, 2015 - 5:42 PM

McPherson sway bar will not work with Super strut geometry

This post has been edited by BonzaiCelica: Oct 11, 2015 - 5:43 PM

edophos my cars not to low, but we all know that with macpherson even lowering 1.5" the control arms start to point upwards and the geometry is off. as for handling for a macpherson its pretty good, im able to keep up with s2000 and sti's in the corner and they are experienced drivers too, its just i lack corner exit traction from lack of an lsd. my bumpsteer has been measured and corrected to move no more than .006" from static to full compress.

sorry that was off topic a little, but how do you guys think the toyota superstrut is compared to fords revoknuckle? fords system seems to be very simple with less pivoting points. seems like their focus was to fix SAI, which seems like a good thing cause less SAI paired with an ideal scrub radius will work really well together to manage torque steer and making your geometry changes count. this is somthing that is harder to do on a macpherson setup since SAI can move your scrub radius to a good or bad position, but the strut mount being so high up seems to be limited, due to the physical restraints of the wheel and strut touching each other.

the one difference i see on toyota's superstrut is the swing arm. the way its mounted makes it seem like it could very well be like an upper control arm just mounted in a funky fashion, but i could be wrong, it could be just so the lower control arm could move without binding.



This post has been edited by rdyzz: Jan 15, 2013 - 9:43 PM

yo dude check out page 7 of this thread about the discussion on fords revoknuckle

also check out this thread for how to better improve mcpherson setup http://www.6gc.net/forums/index.php?showtopic=80081. I'm sure you can find much more info for 7th gen and 2002-2006 rsx since they both came with mcpherson up front. i guess this is the right area to talk about it??? they are some other thread's i've revived in the suspension/handling subforum

lets keep this thread superstrut only talk here go to this section if you want to talk on how to improve mcpherson :

http://www.6gc.net/forums/index.php?showto...20&start=20

check out from time frame 9:15-11:00 minutes they keep on talking about it and even do the comparison between mcpherson corolla and superstrut corolla. So yea

http://www.youtube.com/watch?v=IzEYySvB89w

another superstrut video of when it first came out in 1990. look from 3:22-6:00. again if only we could understand him.

http://www.youtube.com/watch?v=SbQC5rPmSqc

This post has been edited by BonzaiCelica: Feb 26, 2013 - 2:40 AM

Which one it is my fortune tellers?

This post has been edited by Flyin: May 8, 2013 - 12:13 AM

Thats the normal suspension, see its got a solid lower control arm. The superstrut has two pivoting bars for lower control arms. There is plenty of stuff to read on this website if you check out the stickys- Sticky:The Suspension, Handling, Braking thread. <one subforum for example

A little late on this but again just use the gt4 sway bar AND endlinks and theres NO NEED to cut, weld, fabricate bla bla bla.
To swap over ull need the gt4:
-knuckles
-control arms
-endlinks
-rotors (brake disc)
-caliper
-swaybar
-struts (shock and spring)

Am pretty sure thats it and its all plug n play i dnt have a shop so i can say i didnt fabricate or weld anything"]

McPherson front sway bar will not work on Super strut suspension

This post has been edited by BonzaiCelica: Oct 11, 2015 - 5:45 PM

Lol you cant use the GT sway bar on the SS suspension. The GT lower control arm is in a fixed position relative to horizontal travel, in otherwords it only swings up and down not left and right. The SS lower control arms(or bars, 2 per wheel) pivot to allow the steering to turn.
If you attach a GT swaybar to the GT4 SS suspension you will be unable to turn the steering and the car will only travel in a straight line. Hence why its attached to the strut not the control arm.

Never mind. Reread and spoke out of line

This post has been edited by LimitedGT4: May 8, 2013 - 8:06 PM

Sorry, sometimes its hard to properly explain things in the reply box. The point I was making is that you cant weld the GT lower control arm sway-bar-bracket onto the superstrut suspension, because the SS suspension's travel not only goes up and down but left and right as well when you turn. The SS has the sway bar mounted to the strut because it doesnt pivot along a horizontal plane as much; in addition the SS has a longer end link to account for the remainder of the horizontal swing of the SS suspension when turning.

^^at least thats what I deduce from the information on this forum and thread.

This post has been edited by Special_Edy: May 10, 2013 - 9:55 AM

guide to converting superstrut to mcerphson will be made in separate thread. link below...

http://www.6gc.net/forums/index.php?showto...p;#entry1030522

This post has been edited by BonzaiCelica: Nov 7, 2013 - 1:21 AM

This post has been edited by BonzaiCelica: Aug 7, 2013 - 1:43 PM

guide to converting superstrut to McPherson will be made in separate thread. coming soon

http://www.6gc.net/forums/index.php?showto...p;#entry1030522

This post has been edited by BonzaiCelica: Oct 11, 2015 - 5:46 PM

omg omg omg omgosh! miracle?!!


http://www.gt4-racing.eu/index.php/toyota-...suspension-arms

This post has been edited by BonzaiCelica: Feb 7, 2014 - 12:51 AM