6G Celicas Forums

3m fusor- i have used it om bedside and roof skins. GM uses something similar on some panels from the factory and they even used something similar on "musclecar" on spike tv for an old mustang roof skin. i think it runs $50 a tube but its well worth it and you won't use much. OR you could sell it to me...

As far as the doors go - if there is a gap you need to hammer and dolly the skin as close to the inner door as possible then seam seal it. the seam seal it just acts a a seal, not a bonder. again your other doors are salvagable and it sounds like you will do less work with them then the parts doors
if you have a welder just weld the holes...you wont be "cutting corners" by using fiberglass....you will be doing it WRONG.
the windows you need to use 3m windshiled urethane. i used 1 tube for both quarter glass'

k, ill try to make a trip down there if i find time tomorrow. any advice as to the proper way of taking it out though? my instincts tell me to pry carefully but im pretty sure the outcome would be the same. i noticed that there is alot of sealant holding that window inplace, i think the best way would probably to heat the glue from inside the car until you can easily pry but i dont have a heat gun

the 3m fusor or the toms lip.

Lol. That lip. Is isn't it for preface lift?

its for facelifted coupes/hatches but will fit a preface just fine.

http://video.yahoo.com/watch/1484665/5065235
glass removal

dang, that guy made it look so easy. thanks for the vid.

i dont get to work on her much but this is how she sits. and my quarters should come any day now.




toms lip, and preface fogs...

still looking for side.

This post has been edited by captb: Mar 25, 2010 - 8:06 PM

Props on being innovative enough to mold a lip, major props. Very nice man.

i seriously did my homework on plastic welding. im probably an expert by now. lol.

how bout some input. do you think it needs a grill/mesh?

you might wanna reconsider the front markers. Its mandatory in Hawaii to have reflectors up on the front on the car. Most places wont pass you for saftey, but I got places that pass my car

are you talking about the turn markers or side markers? in the pic the turns are actually dangling in the back of the bumper. i really hope ur not talking about the side markers cus i really like the jdm look.

and how in the world do you not get in trouble for clear lens with white bulbs.

turn signals and front marker/sidemarkers are different
I know you seen my car and im running clear turns and markers **knock on wood** I just chose my roads and time of day travel very very carfully

Hawaii Law states you must have a reflective marker both in front and back, the farthest point forward and to the back for safety reasons. To me and You I really hope if in any case the Cop at the time "sees" your turns for both signals and reflective markers

i got a little worried so i read up a bit. and i think im ok. it says that indicators have to be not less than 15in and not more than 60in from the front . and ya, im with you on hoping they see the turns as reflective markers(thats the closest to the front as you can get ) i think ill run amber sides to make it more belivable... for now. hehe. my only concern now is that with this setup the indicators are always lit. you think id get into any trouble with this?

ok, the indicator problem is solved now back to body work.

Question:
i have seen alot of people remove dents and apply bondo but i noticed that alot of people featheredge the bondo onto the paint. then they paint the entire piece over it. from what i understood, you have to at least lightly sand the existing paint before applying a new coat. wont the clear coat keep the paint from getting a good bond?

follow-up to this question is when im featheredging the bondo to existing paint, the clear coat tends to peel almost as if it were a plastic wrap. and even when i apply primer it is very noticeable where the clear stops and starts. i cant seem to featheredge the clear. is the best way to sand the entire car till the clear is removed? or do as i have seen some due and apply paint remover and try my best to get it to bare metal? i dont know if this will affect the answer but when i see the paint it seems as if it were applied as a single thick layer more susceptable to chipping.

i have to drive this car even as im doing the bodywork. is it alright that i expose the bondo to the elements for days even weeks(ex. rain) or should i apply a thin coat of primer to any unfinished surface and sand it down when i have the time to work on it again?

last question, im also installing a bodykit. should i use a sealer tape(kinda like caulking) similar to the oem kits on the corollas? and if i should, i have only seen clear and black being sold, im thinking black would look best on a red car, any suggestions?

sorry again for all the questions, im kinda a perfectionist and i need help nearly everystep of the way to make sure it turns out perfect.

I will get more in depth later buy in short- sounds like your car has been painted before and basically the whole car will need o be sanded down. I would not sugges stripper unless you can take the car apart becuase it will eat the paint off of anything. I the body filler does not feather as you are booking it then the dent is bigger than you thought or you didn't put enough on

Thanks. id appreciate if you could clarify later. and you are correct, i can tell it has been painted base and clear over the oem paint without primer. as for the featheredging, the body filler is fine the problem is when im trying to featheredge of the existing paint. i can show you a picture of what im talking about but the clear seems to either flake off or acts like a saran wrap type of material. so you can obviously see where i have fixed a dent.

I will get more in depth later but in short- sounds like your car has been painted before and basically the whole car will need o be sanded down. I would not sugges stripper unless you can take the car apart becuase it will eat the paint off of anything. I the body filler does not feather as you are booking it then the dent is bigger than you thought or you didn't put enough on

I will get more in depth later but in short- sounds like your car has been painted before and basically the whole car will need o be sanded down. I would not sugges stripper unless you can take the car apart becuase it will eat the paint off of anything. I the body filler does not feather as you are booking it then the dent is bigger than you thought or you didn't put enough on

looky what i did today..



and yes.. that is coolant on the floor, my new problem.

This post has been edited by captb: May 27, 2010 - 12:02 AM