6G Celicas Forums

Move the fusebox to the trunk?

did you already remove the charcoal canister also?

Charcoal canister was tossed when I did the swap.

I'm going to mount the fuel filter on either the firewall or the side of the frame rail. I'm just going to shorten the fuel line a bit to make it tighter to the body.

I have thought about the water issue, I don't drive the car much, but rain is always an issue. I will block off the fuse box completely. My Idea it to access it from pulling back the fender plastic. Again not a daily driver, I avoid rain, so I'm not worried. If something breaks or goes wrong I will fix it.

The body harness can be done without cutting anything, just removing fenders and re routing everything. The engine harness is the hard part.

I should note, THIS CAR IS NOT A DAILY DRIVER.

I will be ready to head up to RI & Mass in the spring

I would recommend a CAI.

This post has been edited by SupraKid: Oct 17, 2010 - 5:20 PM

Awesome job Jeff - I'm very impressed. I still have that MR2 overflow for you but in case you haven't heard I've run into a few spots of trouble with mine.
I'll try to get over there ASAP

no rush dude, I wont be done for a while.

Hey bro - one thing I do see - stretching the throttle cable that high will cause the car to redline 3 secs after you start it.
Ask me how I know

Hey def, this is gonna look great when its done, however the only problem i see with it is, if you ever DO happen to blow a fuse, its going to be the biggest PITA to change out. i mean, other then that theres really no draw backs, and i dont see how you would be able to extend it a little further for it to be out of the way yet still accessable.

keep this updated though, im really curious to see how it will turn out.

looking good so far though man.

The throttle cable has been routed that way for 3 years with no problem. I'd like a different cable though, something I could hide. If anyone has any ideas let me know.



It would be nice to move it else where but I have nowhere else to hide it. The fender seems like the only place to put it. I agree blowing a fuse will suck, changing a fuse will just take a little longer.


Need a hand here, I'm doing the wiring in my kitchen 2 hrs away from the car.

Which plug is for the altonator? and what is the other one for ? AC?


Thanks guys

maybe a cover for the fuse box

one more






Two of the wires were already cut in the harness, I just cut them closer to the plug. Last wire is black, tied in to one of the conversion splices. Do I need this plug?

neither of those look like the ALT plug to me, jeff.

that last one looks like my o2 plug

Did you do the mod to the throttle cable stay on the Valve Cover? What engine/car does your throttle cable come from? Mine is retarded sensitive to position. If I just have mine running over the IC Piping the wrong way it changes the idle. I too would like one that is able to run somewhere more descretly and perhaps not so sensitive to the positioning.


They aren't - I'd be glad to run out and take a pic and text it to you if you'd like. Do you have pic text?

Take a pic for me I can receive pics, That cable, is just a stock GT cable. I have a throttle cable extender installed. I don't have a pic, but it moves the base of the throttle adjustment back like an inch and a half.

Another one, located in the cabin. I think it has something to do with the AC from the 5th gen. I'd like to know if I can remove this.

Note: I do not have AC

the triangle 3pin IS infact the alt plug on a 5th gen. I removed that plug from DEATHs setup.. it was plugged into a jumper harness to a different style round 3pin. that blue/clear plug is for the a/c. im about 80% sure.

thats what i was telling him in the chat, on my 2nd gen harness, instead of that triangle plug, its a large oval one.
maybe its a 90-92/93+ thing, or maybe a RC thing.

So if both of u guys removed this plug for a jumper harness. Does that mean there is another plug directly on the back of the alt. Meaning the female side is part of the alt unit? From memory I don't remember there being another plug. The wires run into the
Back side of the alt.

I appreciate the help fellas I don't want to remove the wrong wires.

jeff, i never removed the triangle plug, i just have a diffrent style of plug.

you can see the plug for your alt in your earlier pics.

Thats the EB1 plug (if i recall the name correctly). You can cut off the connector and ditch the plug.

http://img.photobucket.com/albums/v139/defgeph/IMG_6678.jpg