6G Celicas Forums

anybody know if there's a way to put the 7g leather seats into my 97? i bought them on a whim and obviously they are not going to fit, anyone kno if theres someone out there who has done this successfully? thanks.

Try using the wonderful search function we have on this site.

http://www.celica-club.co.uk/wiki/index.ph..._seats_in_Gen_6

http://www.6gc.net/forums/index.php?showto...l=7th+gen+seats

http://www.6gc.net/forums/index.php?showto...l=7th+gen+seats

Just some links I found after a quick 30 second search.

You can, but you don't need to do any welding. Swap the metal bracket under the 6th gen seat onto the 7th gen seat and then use the 6th gen rails. Easier said than done but it's not hard at all...

i'll give it a shot thnx guys

those seats weigh the same as our stock ones right??

I didn't notice much difference. Probably within a few lbs of each other.

dang..7g seats look sweet

the seats in my 7g have airbags in the sides, which I'm sure would make them heavier than stock 6gc seats, the non-airbag ones are probably about the same weight

Cant find swap info without welding. A write up from you would be great but you've done it already and missed taking pix.

I was originally going to take pictures but it's really not hard so I didn't bother making a write up. Here's the general idea of what you have to do-

Remove the 6g seats from the car. Get a flat head screw driver and start by removing the plastics coverings on each side of the seat. Here is where all the mounting tabs are-



To get the height-adjustment knob off, take a rag and pull it across the c-clip to remove it. (You can see it in the picture) Or a flathead screw driver works too.

Then remove the brackets from the seat- 4 bolts on the bottom, and there are maybe 2 on each side of the back cushion. Once the bolts are out the seat should more or less come apart from the bracket.

There is a bar that runs through the bottom of the back-cushion for the 'reclining' function. This is the hardest part (you'll see) of the whole swap when you're putting it back together.

Once you have the cushions and brackets removed, start by removing the metal support from the bottom of the seat. There are hog-ties and a plastic 'rail' they you need to remove.



Once they're removed, the metal support piece will come away from the cushion. You need to swap this piece from the 6g cushion to the 7g cushion. The bottom cushion of the two seats is identical, but the "metal support piece" has the two front holes in a different place, that is why you need to swap it from the old 6g seat to the 7g seat (so you can bolt the seat to the 6g brackets).

Once you have that swapped, you can start putting the seat back together. The bar that runs through the bottom of the back-cushion can be tricky to put in without the seat falling apart. It helps if you thread the bolts in just slightly to keep the cushion in place while you're aligning that bar. (you'll see what I'm talking about when you go to do it)

Once the bar is back in, tighten the 8 seat bracket bolts and test the reclining function to make sure you got the bar in there correctly. If it works, you're ready to start on the other front seat.

Hope these instructions help. Post back if you need any help.

Good post man seems way easier then welding.






all you needa to now, is come to jersey and drop those seat at my house

cool! nice info! will try 'em soon! still looking for a 7gc cloth seats

So I am in the middle of this project myself, with the seats apart in front of me. Can anyone confirm that the picture he has up of the bottom of the 6g seat is in fact the newer style 6g seat that wasn't the same as the 94 ones? I am running into a much different looking seat bottom and it is keeping me from getting these swapped over. I'm about to try welding this up instead..



This post has been edited by jcbass7: Nov 25, 2010 - 11:04 PM

if it works, this should be stickied. a lot of people want to do this. im looking into doing this with the 7g cloth seats.

7th gen seat pan (2000)


6th gen seat pan (1994)


This post has been edited by jcbass7: Nov 26, 2010 - 12:14 AM

6th gen pan 1995

When you get to the part putting the seat back together, the back of the seat doesn't have any place to screw it in since we are using the 6g brackets. so what do you do there?

I used the 6th gen plastics as well and it all worked perfect. in the car now..

how did you put your seat back together?

sorry i read your post wrong, I used the 6th gen rails and seat bottom complete assembly and swapped the foam and leather seat cover from the 7th gen. The seat backs for the 7th gen and 6th gen bolt in exactly the same with two bolts and a solid steel bar that runs across. the steel bar fits into a small notch on each side. I can try to get pictures later.

so theoretically if you wanted 7th gen seats you could just swap the back of the seat over and keep your 6th gen bottoms (which have a bit more support on the sides..)

This post has been edited by jcbass7: Dec 9, 2010 - 8:59 PM