6G Celicas Forums

why ? do you think my car gonna explode if i push the gas lololol

This post has been edited by Needles: Dec 17, 2011 - 11:09 AM

Lets see.

Your sitting on this:

While being propelled by this:

While riding on this:



Yea 100mph in that is totally safe.

^^good points

final destination 6 could use you

woooooooooooow



i just say in my last post that i have put back the original seat..............................

the orange strap is not there, was for 1 day test ,

............................................................
.

you know what, im tired of this **** always supra kid and ppl say , bs about my car in my thread, im not motivating to post here no more

bye

This post has been edited by Needles: Dec 19, 2011 - 3:00 PM

fix your stuff and we won't give you sh!t. we care about your car not falling apart, and you not dying..

This post has been edited by mkernz22: Dec 19, 2011 - 12:09 AM

ok oki
thanks for the warning,

but if my car is unsafe, i just have to trash it...
i looked at it carefully , a lot of time, and there is a hole on the very inside part of the wing, whit a little bit of rust around,
the work im gonna do on it not gonna change the STRENGH OF THE FRAME , I WILL ONLY DO SOME METAL PATCH to avoid the water going thru there.
so, that mean it gonna have the same rigidity after repair, so , that mean even after the fix, my car will HAVE THE SAME RIGIDITY.

thank for worries, but i will never drive a car that the back suspension is about to break,
its solid, its a hole that need to be pachted and rust free, IST NOT A FRAME THAT HAD BEEN BROKE UNDER PRESSURE OR SO,

its a hole and i will pacht it

its the anti=thief alarm light,
its there since i buy the car

i just put winter tire on the celi and using it when times are good.
i continue finishing the inside and im triyin to keep the vent in the middle,




Uploaded with ImageShack.us


Uploaded with ImageShack.us[/URL
[URL=http://imageshack.us/photo/my-images/810/1327604805521.jpg/]

Uploaded with ImageShack.us

got new muffler today, its only 2,5 inch but i dont need more
i know my exhaust is 3 inch , but the muffler come from a 295hp mustang ,
i got it cheap for 130 $
i hope its gonna sound good


Uploaded with ImageShack.us


Uploaded with ImageShack.us

This post has been edited by Needles: Jan 27, 2012 - 12:58 PM

Fix your rust.

i have put one aluminium plate to protect the interior wing until ill fix it, its not getting worst for now,
but its just that i cant do rust job outside now because its snowing and i cant do it outside during winter, i need to find a garage for 2 or 3 day...

just a little night shot


Uploaded with ImageShack.us

car stop suddently
the efi fuses blew up,
so i change it and it blew again, and then i search for a short,
found that behind the engine, on the firewall, the main wiring harness was hit by the engine when accelerating creating 3 wire to been cut and touch the engine ground.....not good

i just loom it back all good and change the position of the harness behind the engine and fix it there whit tape so it not moving, also,
i have dismount the engine fusesbox because changing the efi fuses didnt work first time,
i did need the replace the wire inside the fusesbox cause it was completly burn,

but now my car have more power at low rpm , maybe the short cut that had the main harness was really bad..

anyway, fixed

This post has been edited by Needles: Jan 29, 2012 - 9:11 PM

i start this by unmount the lens of my old headlight,



Uploaded with ImageShack.us

and say bye bye to the middle front angel eye and projector....


Uploaded with ImageShack.us



Uploaded with ImageShack.us



Uploaded with ImageShack.us



Uploaded with ImageShack.us

cleaning up the glue is a big messy job..


Uploaded with ImageShack.us



Uploaded with ImageShack.us



Uploaded with ImageShack.us

and my goal is to put the projector bi-xenon angel eye into the low beam and create my own pattern , or try immitate the clear kouki one,



Uploaded with ImageShack.us



Uploaded with ImageShack.us



Uploaded with ImageShack.us

im getting the old lenses to a compagny of acrylic near my home so they will do mold and make new clear from it, i also send my turn signal,

.......they wont do it, its like 300$ each piece......

so...i dont know what to do but i got one ideas...

why cant i drill hole in the original glass and put fiber glass there,
i mean, drill the original glass the hole big like the projector of the clear one and keed the side of the headlight frosty like the clear one,
.....

Please. For the love of god learn proper english. You cannot "drill a hole" into glass. But please, by all means, try.

why would you put fiberglass on glass? FIBERGLASS IS FOR BODYWORK, NOT HEADLIGHTS.

and why not try to make your own molds, it shouldn't be too hard to do.

This post has been edited by mkernz22: Feb 1, 2012 - 12:02 AM

I think he means PLEXIGLASS... jrunik just sold some clear lenses for just this purpose , but he took the pic off of his FS thread