power window rollup wont work...arghhh, ...can someonbe please help me on this Options

[lubu]

ok..so i got a window rollup module, but after everything is wired i get three clicks coming from the module everytime it receives a signal...and the windows wont roll up. wtf??
i connect:
the red wire to the + ter
the yell wire to the ignition ON
blacky to - ter
...powerout from the module i connect them to the green & red wires of the motor..
....signal wire is connected to the actuator....

...and...click...click...click....

can anyone please shine a light for me on this..i have been looking at it for the past 3 hours but...*sigh*

thanks

[Hanyo]

what are you using to activate the module?

you need a constant negative ground for the window module to work.
(this may very depending on each manufacture. but the general installation requires this)

[lubu]

im using a negative wire of the actuator of the driver's door.which might not be correct..(blue/white)
can you tell me all the wire colours that i have to connect the module to in order for it to work, thanks

edit: i found a link http://www.caraudiomag.com/technical/0508c..._window_module/ it says that i need to slice one of the motor wire and connect the two wires
from the module to it...but thats a roll up/dn module (fig2). mine is only up..so i don think i need to cut anything do i?



This post has been edited by lubu: Apr 8, 2007 - 1:01 AM

[lubu]

...here is a diagram for my setup http://home.exetel.com.au/lubu/module..

[Hanyo]

i'm slightly confused..


can you show me the wire diagram on the window roll up module.
for my set up i had to cut the motor wire also.

here are the wire colors for the windows on the celica:

LF Window up/down Green - Red Drivers Door Switch
RF Window up/down Grn/Wht - Red/Blu Driver Kick Panel
LR Window up/down Grn/Wht - Red/Wht LR window switch
RR Window up/down Green - Red RR window switch

[lubu]

ok....so which wires i have to cut and join with those coming from the module?
yea the diagram i showed you is similar if not exactly same as the module's manual. those wires are coming out from the module.
LF n RF i understand but LR n RR, r those stands for left and right rear?? celica only has two door isnt it?
...confused...

This post has been edited by lubu: Apr 8, 2007 - 4:03 AM

[Hanyo]

The celica convertable have rear windows. Since you didn't state what kind of celica you own, i decided to post all four windows just incase.

well, if this is the standard window roll up module. Then you will need to cut the green and green/white wires at your window switch and attach it to your module. just like figure 2 of your diagram.

I dont understand why you would need a relay.
another thing to note is, you do not need to attach the green/yellow wire to your acc.

try that and let me know if it works.

This post has been edited by Hanyo: Apr 8, 2007 - 7:50 AM

[lubu]

ok, i'll try that tomorrow..just bak from movie... 300..its awesome.


just to make sure, abt the signal which wire should i connect it to?
....thanks

ED: i opened the module today, changed the configuration abit. Originally it has 5 doors as factory settings, so i turned the other 3 jumpers off.
now it gives me 1 click then a long pause then another click......think the pauses are meant for rolling up the windows.
oh well..let u know tomorrow

This post has been edited by lubu: Apr 8, 2007 - 11:25 AM

[Hanyo]

it depends on what module it is.

i think your module rolls up one window at a time. So the first click is the first window, and the second click is the second window to be rolled up.