mounting the cruise control actuator elsewhere? |
mounting the cruise control actuator elsewhere? |
Mar 30, 2013 - 10:46 PM |
|
Enthusiast Joined May 13, '06 From Kaimuki, HI Currently Offline Reputation: 10 (100%) |
Has anyone else considered mounting the cruise control actuator somewhere else? Below is what I have to work with..haha. I thought about cutting a hole in my custom airbox and mounting it sideways in there. Other than that I have that big gap area around the distributor and behind the intake piping, but I would need a shorter cable running to it from the firewall. What do you guys think?
-------------------- -Jay
95 GT conv. project car: Manual, Gen III 3sgte, JN pisons, Eagle rods, overbore, crank knife-edged, crank scraper, ARP head/main/flywheel, Autronic EMS, Haltech Dual Wideband O2 controller, Audi 1.8T individual coils, FMIC and SSQV BOV, 3" downpipe, 3" ultra-high-flow cat, 2.5" Borla muffler, +other 01 S2000: FMIC, Haltech EMS, Haltech wideband, 570cc inj, forged pistons/rods, sleeved block, 5 angle valve job, ported and polished 02 R6, all stock, except for braided stainless brake lines, frame sliders, and adjustable brake/clutch leve |
Mar 30, 2013 - 11:35 PM |
|
Enthusiast Joined Dec 8, '03 From Lancaster CA Currently Offline Reputation: 6 (100%) |
you could mount it on the passenger side like the ST has it. just extend the wiring
-------------------- 2001 Celica GT-S Turbo
1997 Supra TT 6speed 1997 Celica 3MZ/1MZ swap 1990 Celica All-Trac |
Mar 30, 2013 - 11:47 PM |
|
Enthusiast Joined May 13, '06 From Kaimuki, HI Currently Offline Reputation: 10 (100%) |
you could mount it on the passenger side like the ST has it. just extend the wiring Oh yeah, there is a nice little gap over there between the coolant filler neck and the power steering reservoir. Anyone have pics of the 7a setup? I would also need the cruise control cable from the 7a ST though wouldn't I? -------------------- -Jay
95 GT conv. project car: Manual, Gen III 3sgte, JN pisons, Eagle rods, overbore, crank knife-edged, crank scraper, ARP head/main/flywheel, Autronic EMS, Haltech Dual Wideband O2 controller, Audi 1.8T individual coils, FMIC and SSQV BOV, 3" downpipe, 3" ultra-high-flow cat, 2.5" Borla muffler, +other 01 S2000: FMIC, Haltech EMS, Haltech wideband, 570cc inj, forged pistons/rods, sleeved block, 5 angle valve job, ported and polished 02 R6, all stock, except for braided stainless brake lines, frame sliders, and adjustable brake/clutch leve |
Mar 31, 2013 - 6:51 AM |
|
Enthusiast Joined May 29, '09 From Gainesville, FL Currently Offline Reputation: 17 (100%) |
you could mount it on the passenger side like the ST has it. just extend the wiring Oh yeah, there is a nice little gap over there between the coolant filler neck and the power steering reservoir. Anyone have pics of the 7a setup? I would also need the cruise control cable from the 7a ST though wouldn't I? That gap is for the ABS, but does provide some room for you. The cruise control on a ST is located where the Power Steering Res is located. Shown below. Would be an interesting mounting, but I'm sure feasible! |
Lo-Fi Version | Time is now: November 25th, 2024 - 4:45 PM |