 boost gauge help, aem digital gauge |
 Mar 30, 2013 - 8:02 PM
|
 
|
 Enthusiast  Joined Aug 12, '07 From Lancaster, Pa Currently Offline Reputation: 35 (100%)  |
i have a 2nd gen 3sgte swapped in a 1995 celica. i installed an aem digital boost gauge. i have the gauge grounded properly an the positive side is connected to the radio fuse. i tried tapping into to locations to get a vacuum reading. first the map sensor line and second on the timing belt side of the the engine, on the intake manifold. i get wrong readings in both cases. i check the aem pressure sensor and everything checks out fine. any suggestion, or wisdom is greatly appreciated.
-------------------- |
 |
Replies
|
Apr 3, 2013 - 9:00 AM
|
|
|
Enthusiast Joined Dec 8, '03 From Lancaster CA Currently Offline Reputation: 6 (100%) |
for future reference, almost all digital/electrical gauges need to be on a constant 12V source. something that does not get turned off when you turn the key to start.
-------------------- 2001 Celica GT-S Turbo
1997 Supra TT 6speed 1997 Celica 3MZ/1MZ swap 1990 Celica All-Trac |
|
Apr 3, 2013 - 9:27 AM
|
|
|
Enthusiast Joined Aug 12, '07 From Lancaster, Pa Currently Offline Reputation: 35 (100%) |
i know. i powered it to to radio fuse... didn't work, so i went off of the ignition.
-------------------- |
|
Apr 15, 2013 - 3:04 AM
|
|
|
Enthusiast Joined Apr 15, '13 From Mauritius Currently Offline Reputation: 0 (0%) |
Hello friends...Hey any1 can help me on an st205 stock engine...Where should i connect my boost gauge vaccum line on the inlet manifold?????, i'm not using charcoal canister ..any1 plz? send me some pics or explain briefly plz
This post has been edited by chrismru: Apr 16, 2013 - 1:23 AM |
Posts in this topic
garin boost gauge help Mar 30, 2013 - 8:02 PM
Syaoran Use any nipple from the intake manifold. What do y... Mar 30, 2013 - 8:21 PM
garin it reads 22 psi at idle... not 22 inhg. im thinkin... Mar 30, 2013 - 8:24 PM Syaoran QUOTE (garin @ Mar 30, 2013 - 9:24 P... Mar 30, 2013 - 9:42 PM garin i suppose that is good advice. only got this one t... Mar 30, 2013 - 9:47 PM garin still no luck when the car is on, but not running ... Mar 30, 2013 - 10:35 PM match220 QUOTE (garin @ Mar 30, 2013 - 3:02 P... Mar 30, 2013 - 10:39 PM garin yea i switched it to the other side of the intake ... Mar 30, 2013 - 10:49 PM match220 QUOTE (garin @ Mar 30, 2013 - 5:49 P... Mar 30, 2013 - 11:04 PM garin but would that cause the gauge to read 22psi at id... Mar 30, 2013 - 11:12 PM match220 QUOTE (garin @ Mar 30, 2013 - 6:12 P... Mar 30, 2013 - 11:24 PM garin there is no selector switch on the back.
i figure... Mar 31, 2013 - 8:10 AM match220 QUOTE (garin @ Mar 31, 2013 - 3:10 A... Mar 31, 2013 - 6:44 PM garin these gauges seem to be nice, but quirky at the sa... Apr 1, 2013 - 6:06 PM match220 QUOTE (garin @ Apr 1, 2013 - 1:06 PM... Apr 1, 2013 - 6:40 PM lagos QUOTE (garin @ Apr 1, 2013 - 7:06 PM... Apr 2, 2013 - 12:03 PM garin QUOTE (lagos @ Apr 2, 2013 - 1:03 PM... Apr 3, 2013 - 8:41 AM 83841 im using AEM (psi) Boost gauge which works flawles... Apr 15, 2013 - 12:18 PM paul52 im about to buy an aem tru boost controller'? ... Aug 19, 2013 - 11:02 PM match220 QUOTE (paul52 @ Aug 19, 2013 - 6:02 ... Aug 19, 2013 - 11:35 PM lagos You really can't beat a basic manual boost con... Aug 20, 2013 - 8:52 AM |
3 User(s) are reading this topic (3 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: December 3rd, 2024 - 10:35 AM |