 will the hatchback side skirts fit the convertible? |
 Jun 14, 2013 - 2:50 PM
|
 
|
 Enthusiast  Joined May 13, '06 From Kaimuki, HI Currently Offline Reputation: 10 (100%)  |
I have always been told that the nice side skirts from the hatchback will not fit the convertible because of a different length. However, when I went to the junkyard yesterday I brought my measuring tape. The side skirts had been taken off of the hatchback there, but I measured it from wheel well to wheel well, and it was 70.5 inches. I measured mine when I got back home from wheel well to wheel well the best I could even though my little black side skirts were in the way. It measured out to be about 70.5. This is an approximate measurement since my side skirts were in the way of me doing an exact measurement, but it seemed almost the same. Can someone verify this for me? There were many times that I could have gotten side skirts and didn't because I was told they wouldn't fit
 . If it is 1/4" or 1/2" off, I can modify it to fit since it is so close to being able to fit.
-------------------- -Jay
95 GT conv. project car: Manual, Gen III 3sgte, JN pisons, Eagle rods, overbore, crank knife-edged, crank scraper, ARP head/main/flywheel, Autronic EMS, Haltech Dual Wideband O2 controller, Audi 1.8T individual coils, FMIC and SSQV BOV, 3" downpipe, 3" ultra-high-flow cat, 2.5" Borla muffler, +other 01 S2000: FMIC, Haltech EMS, Haltech wideband, 570cc inj, forged pistons/rods, sleeved block, 5 angle valve job, ported and polished 02 R6, all stock, except for braided stainless brake lines, frame sliders, and adjustable brake/clutch leve |
 |
Replies
|
Jun 14, 2013 - 6:19 PM
|
|
|
Enthusiast Joined May 13, '06 From Kaimuki, HI Currently Offline Reputation: 10 (100%) |
nice..but me getting a lip in Hawaii would be ridiculous on shipping. It's way too large to ship for cheap.
-------------------- -Jay
95 GT conv. project car: Manual, Gen III 3sgte, JN pisons, Eagle rods, overbore, crank knife-edged, crank scraper, ARP head/main/flywheel, Autronic EMS, Haltech Dual Wideband O2 controller, Audi 1.8T individual coils, FMIC and SSQV BOV, 3" downpipe, 3" ultra-high-flow cat, 2.5" Borla muffler, +other 01 S2000: FMIC, Haltech EMS, Haltech wideband, 570cc inj, forged pistons/rods, sleeved block, 5 angle valve job, ported and polished 02 R6, all stock, except for braided stainless brake lines, frame sliders, and adjustable brake/clutch leve |
Posts in this topic
match220 will the hatchback side skirts fit the convertible? Jun 14, 2013 - 2:50 PM
richee3 Njccmd has has two different sets of hatch skirts ... Jun 14, 2013 - 3:53 PM MaskedMan All skirts are the same length. In order to insta... Jun 14, 2013 - 4:21 PM
match220 QUOTE (MaskedMan @ Jun 14, 2013 - 11... Jun 14, 2013 - 4:26 PM MaskedMan QUOTE (match220 @ Jun 14, 2013 - 2:2... Jun 14, 2013 - 6:03 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: December 2nd, 2024 - 3:34 AM |