what are your air intake temps? |
what are your air intake temps? |
Aug 3, 2013 - 5:06 PM |
|
Enthusiast Joined May 13, '06 From Kaimuki, HI Currently Offline Reputation: 10 (100%) |
Hey guys,
Since I have a Gen III in my st204 w/o a GTFour body kit I've been watching my intake temps carefully. (Autronic brand IAT is mounted as close to the engine as I can get it without it being directly above the engine). When I first finished building the engine for the car I still had the insulation on the hood and had a semi covered enclosure for the air filter. The hottest my air intake would get was 80C (crazy!) and that was sitting in traffic with no airflow over my I/C (front mount). Then driving it was around 65C. At night driving it would go down to 60C. After pondering what to do and talking with some drifting friends, I ended up raising up the rear of my hood 4mm, which isn't even noticeable, removing the weather stripping. And also removing the insulation from the hood and making a full enclosure around the airfilter out of plastic and Plexiglas . NOW my air temps are 60C on a hot day sitting in traffic with no air flow over the I/C, and 45C moving on the freeway on a hot day. At night on the freeway it is 40C. relevant intake info(shortened from above): big fmic (air/air), and Autronic brand IAT mounted two feet from TB inlet, not directly above engine. Numbers below are before and after a full air filter enclosure and raised rear of hood 4mm. -------------------------Before-------After hot day in traffic------80C---------60C hot day on hwy-------65C---------45C night on hwy----------60C---------40C (80c is 176f, 65c is 149f, 60c is 140f, 45c is 113f, 40c is 104f) So now that I've mentioned my numbers, I would like to know what your numbers are. I'm expecting it to be cooler once I get the hood vents. I would like to know what the norm is for this engine. Also please mention if you have the fmic or tmic This post has been edited by match220: Aug 3, 2013 - 5:13 PM -------------------- -Jay
95 GT conv. project car: Manual, Gen III 3sgte, JN pisons, Eagle rods, overbore, crank knife-edged, crank scraper, ARP head/main/flywheel, Autronic EMS, Haltech Dual Wideband O2 controller, Audi 1.8T individual coils, FMIC and SSQV BOV, 3" downpipe, 3" ultra-high-flow cat, 2.5" Borla muffler, +other 01 S2000: FMIC, Haltech EMS, Haltech wideband, 570cc inj, forged pistons/rods, sleeved block, 5 angle valve job, ported and polished 02 R6, all stock, except for braided stainless brake lines, frame sliders, and adjustable brake/clutch leve |
Aug 3, 2013 - 8:24 PM |
|
Enthusiast Joined Feb 11, '08 From Auckland, New Zealand Currently Offline Reputation: 0 (0%) |
my temps are getting up around 40-50c and its winter here im not liking it at all, so im changing to front mount to try and get rid of this heat soak
i can tell 40c is bad heat soak because the turbo only makes tutu on high boost setting, usually it tutu on low boost too when intake manifold temp lower than 30c -------------------- Mike W
1996 Toyota Celica ST205 GT-FOUR GT2860RS turbine, TiAL mvr44, JE 86.5φ piston, Clutchmasters FX400, APEX P-FC 269awhp / 273ft-lbs |
Lo-Fi Version | Time is now: December 2nd, 2024 - 8:39 AM |