 5sgte rwd conversion |
 Apr 16, 2014 - 6:34 PM
|
 
|
|
Enthusiast  Joined Nov 15, '10 From ABERDEEN WA Currently Offline Reputation: 3 (100%)  |
well i've started what most people dont have time for. I'm in the middle of building my 5sgte and Rwd conversion,
I have a couple pictures to start with. If you have any question, just ask.   I'm using a 88 toyota truck rear end 2wd. This rear end is harder to find, because it uses the 8 inch center section. And that comes with 30 spline axles. I'm not using the third member. I went with a toyota v-6 4x4 3rd member, that will allow you to buy a supra lsd that will bolt into the v-6 housing. I'm going to be using the stock v-6 gears that comes with 4.10 gears, It may be a little high, but i'll run those for a little bit. Also when i have the lsd out, i'm install a WEIR MAXGRIP LSD Kits It increases the locking force of the clutches. So i'll be posting pictures as i go. This post has been edited by toy8490: Apr 16, 2014 - 6:43 PM |
 |
Replies
|
May 5, 2014 - 3:49 PM
|
|
|
Enthusiast Joined Dec 8, '03 From Lancaster CA Currently Offline Reputation: 6 (100%) |
the R154 must have been in the MKIII because the MKIV non turbo got the W58
With all that work you are doing, why on earth are you using a 5S-FE? wouldnt a V6 or 3S-GTE be more satisfying? -------------------- 2001 Celica GT-S Turbo
1997 Supra TT 6speed 1997 Celica 3MZ/1MZ swap 1990 Celica All-Trac |
|
May 5, 2014 - 9:29 PM
|
|
|
Enthusiast Joined Nov 15, '10 From ABERDEEN WA Currently Offline Reputation: 3 (100%) |
QUOTE (Smaay @ May 5, 2014 - 4:49 PM)  the R154 must have been in the MKIII because the MKIV non turbo got the W58 With all that work you are doing, why on earth are you using a 5S-FE? wouldnt a V6 or 3S-GTE be more satisfying? You must of not read anything i posted, I'm doing a stroker version of a 3sgte, so instead of a 2.0L engine, its going to be a 2.2L engine. You take a 2.2 camry block and use the 3sgte cylinder head. And also I dont know how you came up with a w-58 tranny that i'm using. I wrote on the 1st page that i'm using a toyota pickup transmission out of a v-6 2wd, they come with a r-150 tranny, its just about the same trans as the supra, except 1st and 2nd gear ratio is different, and 5th is different, but overall just as strong as the supra tranny, because its in the same R family trans. This post has been edited by toy8490: May 5, 2014 - 9:32 PM |
Posts in this topic
toy8490 5sgte rwd conversion Apr 16, 2014 - 6:34 PM
toy8490 Fitting the engine and transmission, Dont worry, t... Apr 16, 2014 - 7:18 PM toy8490 I'll be using a 1990 ford mustang rack and pin... Apr 16, 2014 - 7:25 PM Fate looking forward to this build, awesome work thus f... Apr 16, 2014 - 8:03 PM JoshuaM Wow, that's awesome!!! Apr 16, 2014 - 8:36 PM smkr3w Should be awesome. Definitely going to watch this... Apr 16, 2014 - 8:57 PM cardshark525 At least she'll have a low center of gravity ... Apr 16, 2014 - 9:05 PM playr158 if you're using the 5sfe block, what transmiss... Apr 16, 2014 - 9:18 PM cheela subscribed! Apr 16, 2014 - 9:28 PM
toy8490 QUOTE (cheela @ Apr 16, 2014 - 10:28... Apr 16, 2014 - 10:59 PM Smaay i believe that is an R154 transmission or is it t... Apr 16, 2014 - 11:04 PM Box R154 was in the Supra Turbo, W58 was in the non tu... Apr 17, 2014 - 1:19 AM ILoveMySilly97 Nice. A 5sgte that's something uncommon and es... Apr 17, 2014 - 2:12 AM playr158 W58 requires a 2s bell housing to mount to the 5s/... Apr 17, 2014 - 8:12 AM njccmd2002 this is finally happening. RWD conversion... YA... Apr 17, 2014 - 9:04 AM toy8490 The transmission is very close to a r154. The tran... Apr 17, 2014 - 9:40 AM 94GreenLantern NICE! pictures of rear from underneath? Apr 17, 2014 - 9:47 AM mkernz22 Now this is something I might have to do in the fa... Apr 17, 2014 - 12:03 PM toy8490 Heres a picture of the suspension, Not very bright... Apr 17, 2014 - 1:29 PM sandusky1977 If you're going through all that effort, why s... Apr 17, 2014 - 2:08 PM toy8490 This 4 cylinder that i'm building will be ligh... Apr 17, 2014 - 2:14 PM richee3 Very cool stuff. Will this be a DD, track car, dr... Apr 17, 2014 - 2:16 PM Box QUOTE (richee3 @ Apr 17, 2014 - 2:16... Apr 17, 2014 - 2:26 PM toy8490 QUOTE (richee3 @ Apr 17, 2014 - 3:16... Apr 17, 2014 - 3:59 PM toy8490 Heres some more pictures, with the engine all clea... Apr 18, 2014 - 1:54 PM CrossCudi AWESOME ! Apr 18, 2014 - 2:05 PM Box I wonder how such a severe tilt will effect things... Apr 18, 2014 - 3:31 PM SupraKid *Thinks dirty, dirty 2jzgte thoughts* Apr 18, 2014 - 5:01 PM toy8490 Heres some pictures of the rear suspension
The su... Apr 19, 2014 - 10:05 AM toy8490 Now heres some pictures of the steering and engine... Apr 19, 2014 - 10:17 AM team_omega Its looking good. You want to do mines after your... Apr 19, 2014 - 10:48 AM toy8490 QUOTE (team_omega @ Apr 19, 2014 - 11... Apr 19, 2014 - 3:54 PM kormysh8 I can't wait to see the final product. I'v... Apr 19, 2014 - 10:19 PM PR0PH37 Wow. I don't know what the heck I'm lookin... Apr 19, 2014 - 11:19 PM njccmd2002 one questions, those tie rods will be under pressu... Apr 20, 2014 - 7:57 AM toy8490 [quote name='njccmd2002' date='Apr 20,... Apr 20, 2014 - 10:50 AM toyota123 I have to say I'm very intrigued by what you a... Apr 20, 2014 - 10:09 AM LimitedGT4 Sweet.
I was planning on doing somethin like thi... Apr 25, 2014 - 8:49 PM toy8490 Getting closer. Got the struts mounted, so that it... May 5, 2014 - 3:13 PM toy8490 I dont know if this is the same pictures as from b... May 5, 2014 - 3:20 PM mgnt232 QUOTE (Smaay @ May 5, 2014 - 4:49 PM... May 5, 2014 - 4:26 PM Smaay no i dont read everything, i dont need to read 3 w... May 5, 2014 - 9:59 PM cardshark525 Franken-build progressing nicely.
A rwd 6gc runni... May 5, 2014 - 10:32 PM toy8490 i'll be uploading more updates tomorrow of my ... May 11, 2014 - 10:38 PM toy8490 Well was almost done, had the complet dash inside ... May 12, 2014 - 12:34 PM Special_Edy Im far from being an expert, and Im having difficu... May 12, 2014 - 2:09 PM toy8490 Here some more progress pictures, motor mounts / t... May 15, 2014 - 10:00 AM njccmd2002 wow this is significant progress. May 15, 2014 - 11:52 AM Malek Seriously! ^^
This is some good stuff! May 15, 2014 - 1:54 PM ClevelandGaint I want this May 15, 2014 - 3:47 PM playr158 its crazy.....its impractical.....its freaking awe... May 15, 2014 - 9:29 PM jeffrosie Awesome build M8.
Was just thinking, why not use t... May 16, 2014 - 6:04 PM Special_Edy Naw he should use the straight axle. Maybe get a s... May 16, 2014 - 7:13 PM lagos Impressive project! May 17, 2014 - 9:46 AM toy8490 I hope you guys are ready for this, I'm gettin... May 31, 2014 - 11:31 PM toy8490 Picture time, I love it.
I'm going ... May 31, 2014 - 11:38 PM Box It's so weird seeing the engine longitudinally... May 31, 2014 - 11:50 PM BonzaiCelica wow at that point why not fit the intake manifold ... Jun 1, 2014 - 3:25 PM playr158 So much awesome. Jun 1, 2014 - 7:39 PM Batman722 IC piping is gonna be funky. I see a lot of lag co... Jun 1, 2014 - 8:20 PM LimitedGT4 QUOTE (Batman722 @ Jun 1, 2014 - 8:2... Jun 1, 2014 - 8:26 PM toy8490 I already have the front mount Intercooler from my... Jun 2, 2014 - 6:20 PM toy8490 got the intake modified, it fit perfect. Jun 23, 2014 - 12:45 AM njccmd2002 dang... thats a nasty beautiful intake..... glad ... Jun 23, 2014 - 11:48 AM Malek truth ^^
This thing is sweet Jun 23, 2014 - 4:23 PM ricochet1490 nicely done. I appreciate the fabrication here. Jul 6, 2014 - 8:11 PM dudeofchaos Woww. I wanted to do this for years with my st204 ... Jul 14, 2014 - 5:02 PM BonzaiCelica update? so rare! Jul 28, 2014 - 2:05 PM HaysoosKreesto wow, it's like you took every st204's fant... Jul 28, 2014 - 5:17 PM toy8490 I just now got the car running today, Just have to... Aug 20, 2014 - 2:16 PM Box I can't believe you think this is taking awhil... Aug 20, 2014 - 3:40 PM IllIllIll When I first saw the thread I assumed that this wo... Aug 30, 2014 - 9:39 AM toy8490 QUOTE (IllIllIll @ Aug 30, 2014 - 9... Oct 12, 2014 - 1:57 PM mkernz22 RE: 5sgte rwd conversion Oct 12, 2014 - 2:11 PM toy8490 I hope this works
http://vid266.photobucket.com/a... Oct 12, 2014 - 9:50 PM toy8490 QUOTE (toy8490 @ Oct 12, 2014 - 9:50... Oct 17, 2014 - 9:54 AM Syaoran oh boy Oct 12, 2014 - 9:52 PM mkernz22 That a$$ end is way high! Oct 12, 2014 - 11:13 PM HaysoosKreesto That sound makes my face look like that Kim Kardas... Oct 12, 2014 - 11:22 PM enderswift holy crap you finished O.O
good work! Oct 13, 2014 - 12:06 AM kurt95gt This is crazy!
Love it! Oct 14, 2014 - 12:44 PM SwissFerdi Nice! Good on you, man. You've done what 9... Oct 15, 2014 - 10:11 AM njccmd2002 And people, lot of people, i mean lots of people. ... Oct 16, 2014 - 5:54 PM Box QUOTE (njccmd2002 @ Oct 16, 2014 - 5... Oct 16, 2014 - 6:38 PM Arturio55 This makes the awd conversion look as simple as dr... Oct 16, 2014 - 6:51 PM HaysoosKreesto Worked for me Oct 17, 2014 - 9:59 AM Smaay impressive work....
how are you going to do the i... Oct 26, 2014 - 8:09 PM toy8490 I'm planning on doing my own header and new tu... Oct 27, 2014 - 3:53 PM toy8490 Looking to buy a gt35 twin scroll turbo, I'll ... Apr 2, 2015 - 9:56 AM toy8490 New turbo has made it here. Time for some work now... Apr 21, 2015 - 9:36 AM toy8490 I removed the factory turbo, (which is for sale) ... Apr 25, 2015 - 1:20 PM pitcelica Here's a place where you can find a 3rd gen ex... Apr 26, 2015 - 8:16 AM toy8490 Thank you for the site link for the exhaust flange... Apr 28, 2015 - 9:52 AM toy8490 Started and mostly finished my own built header, I... May 7, 2015 - 9:52 AM bsamps4 Where did you buy the piping? Looks good! May 7, 2015 - 11:48 AM toy8490 QUOTE (bsamps4 @ May 7, 2015 - 11:48... May 7, 2015 - 1:40 PM toy8490 Removed the header so i can weld it up, May 8, 2015 - 9:33 AM bsamps4 Good lord man! I'd never be able to get a ... May 9, 2015 - 10:09 AM |
19 User(s) are reading this topic (19 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: November 22nd, 2024 - 8:21 PM |