 BEAMS gauges in celica GT |
 Jun 16, 2014 - 6:05 AM
|
 
|
 Enthusiast  Joined May 13, '06 From Kaimuki, HI Currently Offline Reputation: 10 (100%)  |
Hey guys,
I bought some BEAMS gauges a while back to put in my celica to take advantage of the tach signal from the ECU (i'm running engine management and no distributor). I heard these were a direct swap, but my fuel gauge isn't working when I put them in. I waited a couple minutes and the gauge didn't climb with the ignition switch turned. Can someone verify that these gauges work in this car? This post has been edited by match220: Jun 16, 2014 - 6:06 AM -------------------- -Jay
95 GT conv. project car: Manual, Gen III 3sgte, JN pisons, Eagle rods, overbore, crank knife-edged, crank scraper, ARP head/main/flywheel, Autronic EMS, Haltech Dual Wideband O2 controller, Audi 1.8T individual coils, FMIC and SSQV BOV, 3" downpipe, 3" ultra-high-flow cat, 2.5" Borla muffler, +other 01 S2000: FMIC, Haltech EMS, Haltech wideband, 570cc inj, forged pistons/rods, sleeved block, 5 angle valve job, ported and polished 02 R6, all stock, except for braided stainless brake lines, frame sliders, and adjustable brake/clutch leve |
 |
Replies
|
Jun 19, 2014 - 7:55 AM
|
|
|
Enthusiast Joined May 13, '06 From Kaimuki, HI Currently Offline Reputation: 10 (100%) |
Here is what I've been able to trace out with the pinout so far. I took pictures of the backs of the gauges so I could draw out the circuits in different colors in mspaint while away from home. Some of the circuits I can't see very well in the pictures, I'll have to wait till I get back home. Definitely different though. The C plug is the most different, the bulbs are offset by 1 pin, not sure what the bulbs are yet though until I'm at the gauges and can flip them over. ST205 gauges has some similarities with the BEAMS gauges as far as the pinout goes.
ST204_______________________________________BEAMS A1__________________________________________A1__ILL A2__________________________________________A2__Bulb A3__________________________________________A3__Blank bulb A4__________________________________________A4__Solder dot A5__________________________________________A5__nothing A6__________________________________________A6__RPM IG- top screw A7__________________________________________A7__bulb? A8__________________________________________A8__all bulbs -? or +? A9__________________________________________A9__bulb A10__Top RPM screw___________________________A10_nothing A11__nothing_________________________________A11_nothing A12__nothing_________________________________A12_bulb A13__RPM mid screw and..._____________________A13________RPM mid screw and B1__L turn___________________________________B1________L turn B2__nothing__________________________________B2________ILL B3__speedo screw TR__________________________B3________speedo screw TR________ B4__________________________________________B4________bulb B5__nothing__________________________________B5________nothi ng B6__RPM bottom screw, speedo LR_______________B6________RPM bottom screw, speedo LR B7__RPM bottom screw, speedo LR________________B7________RPM bottom screw, speedo LR B8__bulb_____________________________________B8________bulb B9__bulb_____________________________________B9________bulb B10__bulb____________________________________B10________bulb B11__bulb____________________________________B11________bulb B12__nothing_________________________________B12_____nothing B13_________________________________________B13_____nothing B14_________________________________________B14________speed o screw TL B15_R turn___________________________________B15________R turn B16__turn signal bulbs and gray box_______________B16________turn signal bulbs and gray box C1__________________________________________C1________fuel top screw C2_temp top screw_____________________________C2________temp top screw C3_nothing___________________________________C3________temp mid screw C4_temp mid screw____________________________C4________bulb________ C5_nothing___________________________________C5________bulb C6_bulb______________________________________C6________bulb C7_bulb______________________________________C7________bulb C8_bulb______________________________________C8________bulb -------------------- -Jay
95 GT conv. project car: Manual, Gen III 3sgte, JN pisons, Eagle rods, overbore, crank knife-edged, crank scraper, ARP head/main/flywheel, Autronic EMS, Haltech Dual Wideband O2 controller, Audi 1.8T individual coils, FMIC and SSQV BOV, 3" downpipe, 3" ultra-high-flow cat, 2.5" Borla muffler, +other 01 S2000: FMIC, Haltech EMS, Haltech wideband, 570cc inj, forged pistons/rods, sleeved block, 5 angle valve job, ported and polished 02 R6, all stock, except for braided stainless brake lines, frame sliders, and adjustable brake/clutch leve |
Posts in this topic
match220 BEAMS gauges in celica GT Jun 16, 2014 - 6:05 AM
njccmd2002 i have them in my car, and work. Jun 16, 2014 - 10:04 PM r3ck0n1ng Does your engine temperature gauge work? If so it ... Jun 18, 2014 - 4:28 PM njccmd2002 Trust me...
http://youtu.be/fugSnfmqS30 Jun 18, 2014 - 11:04 PM match220 My temp gauge isn't even connected anymore. I ... Jun 19, 2014 - 12:08 AM match220 So now I'm comparing the circuitry on the back... Jun 19, 2014 - 1:15 AM njccmd2002 i did not mess with pin outs, each side had 3 or f... Jun 19, 2014 - 1:59 AM
match220 QUOTE (njccmd2002 @ Jun 18, 2014 - 8... Jun 19, 2014 - 3:13 AM match220 I threw the tacho into my cluster and the RPM need... Jun 19, 2014 - 2:33 PM match220 I repinned the connectors, got the full gauges wir... Jun 24, 2014 - 1:22 AM njccmd2002 i dont know why you are having such a hard time...... Jun 24, 2014 - 7:09 AM match220 QUOTE (njccmd2002 @ Jun 24, 2014 - 2... Jun 24, 2014 - 7:49 AM njccmd2002 ok then. see the little triangles on the sides, th... Jun 24, 2014 - 9:20 AM match220 QUOTE (njccmd2002 @ Jun 24, 2014 - 4... Jun 24, 2014 - 9:54 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: November 27th, 2024 - 3:24 AM |