Alwayzsidewayz Project Sky, ST202 UK car total rebuild Options

[alwayzsidewayz]

Hi All,

Been active on the FB pages so thought I should share here.
I am building my dream ST202. I have had a number of Celica’s in my car history, but this one called “Sky” is my forever car. It’s my 100th car I have owned. I have become obsessed with getting this on spot on.
Currently she is in a complete very smart state, awaiting a full tear down from top to bottom and a total new build.
Planned Spec is as follows.
Engine
Based upon a rev 3 3sge block and head
Block – Chemically cleaned, line honed and corrected, 86.5mm bore
Gen 3 Genuine Toyota 86.5mm pistons and completion spec Rings
Forged H Beam lightweight connecting rods
Tri-metal completion bearings
Dynamically balanced, ground and polished crankshaft
ARP cylinder head studs
Competition MLS head gasket
Uprated Piper valve springs
Ported Cylinder head
Shimless “solid” lightweight lifters
Long Duration high lift camshafts (ground from blanks)
Piper Venier Pulleys
Hurley Phenolic inlet gasket
Hurley 45mm throttle body kit, using Jenvy Throttle bodies
Custom intake
Ramair Air filter
Hurley 24-2 wasted spark trigger kit – (magnetti Sensor)
Celica T230 Coil packs
New Injectors
Adjustable fuel regulator
Upgraded fuel pump, twin set up with swirl pot
Alloy Rad
Custom expansion tank
Billet oil cap
Custom painted rocker cover
Ally Catch tank
Aeroquip hosing throughout
Misimoto PAS cooler
New starter motor and alternator
Custom water pump
Remote electrical thermostat
Exhaust is as follows
Japspeed Ceramic coated Exhaust manifold
Decat
HKS Super dragger exhaust system
This will be run on a custom loom by a link G4+ Fury ECU

Transmission
S54 box fully rebuilt
Kaaz LSD
ARP flywheel bolts
Hurley lightweight 3sge flywheel
Black diamond stage 2 clutch
Toyota new release bearing
BRD poly gearshift bushes
TRD short shifter kit
New Toyota master cylinder
Rebuilt Drive shafts

Suspension
All new refurbished hubs front and rear
Powder coated rear beam, cross members and wishbones
Super strut front cross members
Super strut steering rack
BRD poly steering bushes
Whiteline and GT4 – play poly bush kit throughout front and rear
Cusco front under brace
Front strut brace
BC BR coilovers
Hardrace rear arms
Ultra rear sway bar
Whiteline drop links
Powder coated front sway bar
GT4 rear strut brace
All new inner and outer tie rods, ball joints etc
All new Toyota bolts, nuts, washers and fixings
Custom spacers front and rear

Brakes
KSport 8 pot front calipers in red with 330mm discs and blue stuff pads
Ksport 4 pot rear calipers in red with TBC discs and blue stuff pads
Custom brake stopper
ABS stripped out
AP racing brake proportioning valve
All new lines

Wheels and tyres
Rays Volk GTP Daytona 17 x 8 lightweight rims
215 40 falken rubber

Body
Battery relocated to the boot
BRD poly engine mounts
Custom vented bulkhead for intake
Seam welded engine bay
Smoothed and tucked engine bay
TBC body kit
Carbon rear plate surround, number plates and window deflectors
Carbon capped mirrors
Smoothed rear tailgate, no badge, or rear wiper or high level brake light
Import rear lights with LED conversion
Rear diffuser
Rolled front and rear arches
All New rubbers
New windscreen
Carbon hood with custom vents
Projector front lights
Crystal indicators
Colour change
Fully painted inside and out

Interior
Dash 2 pro electronic dash
Tablet with Android Link software for centre dash display
Custom leather front and rear seats and door panels
Mono Monte Carlo steering wheel
New carpets
Hyper sport mats
LED interior lighting
Leather trimmed interior inc dash
Alloy pedals and accents etc
Plus More

Current state of play is as follows
I have the engine all built. It’s sat waiting in the garage
17498470_10212145758510341_2285727355440895122_n by Richard Morrow, on Flickr
17458125_10212145758870350_7968047748287389662_n by Richard Morrow, on Flickr

I have pretty much all the parts bar the body kit, rear brakes, and ecu plus dash
Current state of the interior
IMAG3205 by Richard Morrow, on Flickr
IMAG3204 by Richard Morrow, on Flickr
Wheels
IMAG2639 by Richard Morrow, on Flickr
Current engine bay
15541983_10211189839132954_7436297401766375026_n by Richard Morrow, on Flickr

The car is going to go soon up to the shop which is helping me with this, so it can be tore down to a bare shell.

Then it will be stripped back to bare metal, any rust damage etc fixed and the metal work mods can start.

I plan to have the car built over the course of this year and then ready for the 2018 show and track day year.

The car is being built to the best I can do, so it’s all new bolts and the best I can afford in terms of set up.
A set of track rims is under consideration, with track rubber, as the car will see track action, along with show and shine work etc

The car is slightly famous already, I purchased it last summer, from a good friend, who had already started the mods and got the car featured in a car magazine.
IMAG1945 by Richard Morrow, on Flickr

How I first got car
IMAG1944 by Richard Morrow, on Flickr
IMAG1943 by Richard Morrow, on Flickr
IMAG1942 by Richard Morrow, on Flickr


Since I have owned the car, I have added a lot of mods, that I already had, such as Koni adjustable suspension for the front and KYB for the rear with Eibach springs, the rims, the interior, the lights, the HKS and K& N filters, chrome detailing etc.
How she sits right now
16427464_10211671652297982_5365202565806282193_n by Richard Morrow, on Flickr
IMAG2681 by Richard Morrow, on Flickr
IMAG3194 by Richard Morrow, on Flickr

The car is super straight and very very clean; I wanted the best base for the build possible.
Anyway below are a few pics to give you the idea.
https://www.flickr.com/photos/149025875@N03/shares/x8bcRQ
https://www.flickr.com/photos/149025875@N03/shares/z07PT6
https://www.flickr.com/photos/149025875@N03/shares/uR2989
https://www.flickr.com/photos/149025875@N03/shares/z11tK8

This post has been edited by alwayzsidewayz: Apr 1, 2017 - 4:08 AM

[BonzaiCelica]

Wow haven't seen a build like this in a while. Brakes seem overkill? Maybe save the money and go ST205 brakes? But my guess is that you want that set up because you can get a 2 piece rotor configuration...