 after swap, not turning over ?!!?!?!, advise |
 Jan 23, 2006 - 12:21 AM
|
 
|
 Enthusiast  Joined Mar 8, '04 From Newport, RI Currently Offline Reputation: 63 (99%)  |
here is the situation...a 94 5s went into a 96. The 96 harness was used and everything matched up except a few things (they were then swapped over from the 96 motor to the 94, i.e. distributer, OBDII, ect. ). Now after everything is all hooked up and put together, it doesn't start up. It cranks, the starter is good, but no vroom.
anything that I should check for specifically ? any ideas ? wtf ? thanks -------------------- |
 |
Replies
|
Feb 4, 2006 - 6:00 PM
|
|
|
Enthusiast Joined Sep 29, '05 From Rochester, Massachusetts Currently Offline Reputation: 2 (100%) |
it idles at like 2000 rpms now, its a lil high... I have an idea of how to adjust it, but i dont wanna mess w/ anything ya know? and p.s. , I dont have heat either...
This post has been edited by nightryder: Feb 4, 2006 - 6:06 PM --------------------  The question is not how far. The question is, do you possess the constitution, the depth of faith, to go as far as is needed? |
Posts in this topic
Batman722 after swap, not turning over ?!!?!?! Jan 23, 2006 - 12:21 AM
Dr_Tweak Are you getting spark? Is the fuel pump running? D... Jan 23, 2006 - 12:22 AM Batman722 the problem is I am not at the engine to find out,... Jan 23, 2006 - 12:36 AM Dr_Tweak Well, first off, "turn over" = cranking,... Jan 23, 2006 - 12:40 AM Batman722 you are correct, turning over, yes, starting, no.
... Jan 23, 2006 - 12:43 AM Dr_Tweak Yeap, that's probably his problem right there. Jan 23, 2006 - 1:07 AM presure2 he prolly forgot somthing dustin, did he tell you ... Jan 23, 2006 - 9:16 AM Batman722 he swaped the cover and his dad did the timing bel... Jan 23, 2006 - 11:13 AM Agent21 There are supposidly some differences between cali... Jan 23, 2006 - 9:43 PM nightryder ok guys, ill step forward, its my car.
alright...... Jan 24, 2006 - 12:17 PM lagos QUOTE(nightryder @ Jan 24, 2006 - 12... Jan 24, 2006 - 1:19 PM nightryder OK i have an update and an apology for my last pos... Jan 24, 2006 - 1:55 PM Sr_Ric i know on some cars if your using diffrent wiring ... Jan 24, 2006 - 3:38 PM lagos QUOTE(nightryder @ Jan 24, 2006 - 1... Jan 24, 2006 - 4:12 PM nightryder Ive been doing some trouble shooting and i think i... Jan 24, 2006 - 6:23 PM Agent21 Take a multimeter on the positive pole and the lit... Jan 24, 2006 - 7:33 PM
nightryder QUOTE(Agent21 @ Jan 24, 2006 - 7:33 ... Jan 25, 2006 - 9:22 AM Agent21 I only know this because mine blew out of no where... Jan 25, 2006 - 3:26 PM rjbibeau i now too have the same prob as doggy. i swapped f... Jan 27, 2006 - 2:42 PM Agent21 Could be the ignition control module as well. It i... Jan 27, 2006 - 7:43 PM Batman722 The problem is most likely getting corrected right... Jan 27, 2006 - 11:35 PM nightryder QUOTE(Batman722 @ Jan 27, 2006 - 11... Jan 30, 2006 - 12:22 AM rjbibeau i'll check and see. i checked all fuses and al... Jan 28, 2006 - 12:39 AM Agent21 Well the ugly way is to buy one with a return poli... Jan 28, 2006 - 3:16 PM nightryder ok a break in the case! I had a buddy come do... Jan 30, 2006 - 12:19 AM lagos QUOTE(nightryder @ Jan 30, 2006 - 12... Jan 30, 2006 - 12:24 AM nightryder QUOTE(lagos @ Jan 30, 2006 - 12:24 A... Jan 30, 2006 - 12:28 AM lagos QUOTE(nightryder @ Jan 30, 2006 - 12... Jan 30, 2006 - 1:08 AM nightryder QUOTE(lagos @ Jan 30, 2006 - 1:08 AM... Jan 30, 2006 - 1:16 AM Batman722 Nate, I am free tomorrow after 7ish...give me a ca... Jan 30, 2006 - 1:55 AM Agent21 "my wonderful "wrangler enthusiast... Jan 30, 2006 - 2:25 PM nightryder QUOTE(Agent21 @ Jan 30, 2006 - 2:25 ... Jan 30, 2006 - 7:01 PM nightryder And the clouds opened up and god said "Let it... Feb 2, 2006 - 6:58 PM rjbibeau there's a ground on the back of the block?....... Feb 3, 2006 - 10:35 AM presure2 it attaches to the back of the intake manifold. Feb 3, 2006 - 10:36 AM rjbibeau sweet deal maybe that's my problem. where does... Feb 3, 2006 - 10:56 AM nightryder QUOTE(rjbibeau @ Feb 3, 2006 - 10:56... Feb 3, 2006 - 6:15 PM Batman722 Glad to hear the beast is running again Nate
g... Feb 4, 2006 - 1:38 AM rjbibeau good news guys my engine is alive. it runs smooth.... Feb 4, 2006 - 6:44 PM Batman722 Just to let you all know, Nate's (nightryder) ... Feb 14, 2006 - 12:08 AM Dr_Tweak He didn't buy a clip? Feb 14, 2006 - 12:19 AM lagos QUOTE(Dr_Tweak @ Feb 14, 2006 - 12:1... Feb 14, 2006 - 12:25 AM nightryder QUOTE(lagos @ Feb 14, 2006 - 12:25 A... Feb 14, 2006 - 7:33 AM |
5 User(s) are reading this topic (5 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: November 27th, 2024 - 9:07 AM |