6G Celicas Forums

Welcome Guest ( Log In | Register )

> Not getting fuel 3sgte, Getting fuel to filter, no error codes, no fuel on spark plugs, not st
post Jul 10, 2006 - 8:51 AM
+Quote Post
jcbass7



Enthusiast
*****
Joined Apr 20, '06
From Florida
Currently Offline

Reputation: 44 (100%)




The car is ready to run etc. but the problem i am having now is that the fuel pump is not running. I am pretty sure its not the fuel pump with the issue, and ive used a voltmeter to test the lines going to it and they are not bringing power.

Is a relay out possibly? i know the fuel pump needs certian things in the car to work for it to run..

I jumped the +B and Fp terminals and then put the car in the ON position and still no power to the pump


any ideas?

This post has been edited by jcbass7: Jul 22, 2006 - 7:23 PM
 
Start new topic
Replies
post Jul 12, 2006 - 6:55 AM
+Quote Post
Dr_Tweak



Enthusiast
*****
Joined Mar 31, '04
From Summerville, SC
Currently Offline

Reputation: 5 (100%)




You didn't tell me you were having a fuel problem.... which ECU are you using? What year is it from and is it a JDM or USDM ECU? What year was the harness from and again, JDM or USDM. Are you sure the C/OPN relay is plugged in? It's a fairly large relay that is usually either bolted to the ECU or very close to it. You can find it by following the green/red "FC" wire from the ECU, which will be on either pin 14 of the 22-pin connector or pin 17 of the 26-pin connector.

Also, using a volt-meter, check and see if you're getting 12v from the "+B" terminal in the diagnostic block to a ground (with the key on).

-Doc

This post has been edited by Dr_Tweak: Jul 12, 2006 - 7:07 AM


--------------------
-Dr Tweak, 6GC's resident engine swap wiring expert extraordinaire
Click here to see my swaps
drtweak@phoenixtuning.com


Posts in this topic
- jcbass7   Not getting fuel 3sgte   Jul 10, 2006 - 8:51 AM
- - presure2   who did your harness? check the fueses first, make...   Jul 10, 2006 - 9:03 AM
|- - jcbass7   QUOTE(presure2 @ Jul 10, 2006 - 9:03...   Jul 10, 2006 - 9:10 AM
- - lagos   they should be next to your ecu. black one is COR,...   Jul 10, 2006 - 11:35 AM
- - jcbass7   alright ill check the harness to make sure its all...   Jul 10, 2006 - 4:04 PM
- - lagos   QUOTE(jcbass7 @ Jul 10, 2006 - 5:04 ...   Jul 10, 2006 - 4:31 PM
- - jcbass7   yea i haven't been able to reach him for the l...   Jul 10, 2006 - 4:52 PM
- - Dr_Tweak   You didn't tell me you were having a fuel prob...   Jul 12, 2006 - 6:55 AM
|- - jcbass7   QUOTE(Dr_Tweak @ Jul 12, 2006 - 6:55...   Jul 13, 2006 - 12:11 PM
- - jcbass7   ok i charged the batt and i am not getting any pow...   Jul 14, 2006 - 9:11 AM
- - lagos   your COR is probably not wired up right   Jul 14, 2006 - 11:06 AM
- - Dr_Tweak   When you turn the key to the on position, does you...   Jul 14, 2006 - 11:39 AM
|- - jcbass7   QUOTE(Dr_Tweak @ Jul 14, 2006 - 11:3...   Jul 14, 2006 - 4:42 PM
- - Dr_Tweak   Don't worry about that right now, it probably ...   Jul 14, 2006 - 4:49 PM
- - jcbass7   ok 1. the check engine light is not on. and does ...   Jul 14, 2006 - 5:02 PM
|- - Dr_Tweak   QUOTE(jcbass7 @ Jul 14, 2006 - 10:02...   Jul 15, 2006 - 7:31 AM
|- - jcbass7   QUOTE(Dr_Tweak @ Jul 15, 2006 - 7:31...   Jul 16, 2006 - 12:28 PM
- - lagos   QUOTEthe large ground behind the intake manifold ...   Jul 14, 2006 - 5:28 PM
|- - jcbass7   QUOTE(lagos @ Jul 14, 2006 - 5:28 PM...   Jul 14, 2006 - 5:30 PM
- - lagos   there is a ground wire on the back of the motor. i...   Jul 14, 2006 - 5:35 PM
- - jcbass7   shall do good thing the axles aren't in yet gi...   Jul 14, 2006 - 5:37 PM
|- - phattyduck   QUOTE(jcbass7 @ Jul 14, 2006 - 3:37 ...   Jul 14, 2006 - 6:07 PM
- - jcbass7   damn im stupid, alright i have them all hooked up ...   Jul 14, 2006 - 6:16 PM
- - jcbass7   you say it goes to the second runner correct? wel...   Jul 14, 2006 - 6:54 PM
- - Dr_Tweak   Just make sure that ground is bolted to the manifo...   Jul 14, 2006 - 8:48 PM
- - jcbass7   She is bolted on and grounded. still no power to...   Jul 14, 2006 - 10:15 PM
- - lagos   what is the car doing... does the starter even cra...   Jul 14, 2006 - 10:22 PM
- - jcbass7   oh yes the starter cranks fine, my step dad spraye...   Jul 14, 2006 - 10:37 PM
- - lagos   but, you also said that your diagnostic (cel, oil....   Jul 14, 2006 - 10:46 PM
- - jcbass7   its an sw20 pump, and yes i am not getting a che...   Jul 14, 2006 - 10:47 PM
- - lagos   from your battery... you have a ground wire connec...   Jul 14, 2006 - 10:50 PM
- - K-ESD   You're not getting pwr from the EFI relay pull...   Jul 15, 2006 - 12:16 AM
- - jcbass7   ok ny meet is today so ill test all of this tommor...   Jul 15, 2006 - 6:21 AM
- - K-ESD   actualy, i made things a lil more complicated than...   Jul 15, 2006 - 7:18 AM
- - jcbass7   also i tried Art's suggestion with jumping bat...   Jul 16, 2006 - 12:50 PM
- - K-ESD   have you tried what I suggested? cause from your ...   Jul 16, 2006 - 4:04 PM
- - Dr_Tweak   K-ESD is correct, there's nothing wrong with t...   Jul 16, 2006 - 4:29 PM
- - jcbass7   yes i understand that the problem is not the fuel ...   Jul 16, 2006 - 8:01 PM
- - jcbass7   EDIT: I just went out to double check the pink wi...   Jul 16, 2006 - 8:17 PM
|- - Dr_Tweak   QUOTE(jcbass7 @ Jul 17, 2006 - 1:17 ...   Jul 16, 2006 - 8:24 PM
- - K-ESD   you're getting closer relay works so you can m...   Jul 16, 2006 - 8:58 PM
- - jcbass7   i'm going to have to buy more fuses and test i...   Jul 16, 2006 - 11:00 PM
- - jcbass7   ok here is the update... the 15amp fuse blows eve...   Jul 17, 2006 - 8:34 AM
- - jcbass7   OK with tweaks help i have made progress (for anyo...   Jul 17, 2006 - 6:17 PM
- - Dr_Tweak   Hmm this is odd. Yes, code 14 will cause the engi...   Jul 17, 2006 - 7:55 PM
|- - jcbass7   I'm going to have to draw a diagram of this.. ...   Jul 18, 2006 - 10:44 AM
- - lagos   check your harness plug that goes to the ignitor. ...   Jul 17, 2006 - 8:03 PM
|- - phattyduck   QUOTE(lagos @ Jul 17, 2006 - 6:03 PM...   Jul 17, 2006 - 8:33 PM
||- - jcbass7   QUOTE(phattyduck @ Jul 17, 2006 - 8...   Jul 17, 2006 - 9:25 PM
|- - jcbass7   QUOTE(lagos @ Jul 17, 2006 - 8:03 PM...   Jul 18, 2006 - 10:54 AM
- - WannabeGT4   Your ECU is definitely form a 92-93 celica. Looki...   Jul 18, 2006 - 1:52 PM
- - jcbass7   correct i did not buy a clip (mistake) but i actua...   Jul 18, 2006 - 2:14 PM
|- - WannabeGT4   QUOTE(jcbass7 @ Jul 18, 2006 - 2:14 ...   Jul 18, 2006 - 3:06 PM
- - Dr_Tweak   Okay, ECU is correct, the are you sure that the 16...   Jul 18, 2006 - 2:28 PM
- - jcbass7   how about the 26 pin... should that have pins in ...   Jul 18, 2006 - 10:31 PM
- - jcbass7   Ok this diagram shows EXACTLY what my wiring looks...   Jul 19, 2006 - 1:31 PM
- - Dr_Tweak   Okay well the THW is an odd one, there must be a b...   Jul 19, 2006 - 4:05 PM
- - jcbass7   ok so this is a bit weird i thought i might che...   Jul 19, 2006 - 5:58 PM
- - jcbass7   ok well im almost positive code 12 is because the ...   Jul 19, 2006 - 6:06 PM
|- - Dr_Tweak   QUOTE(jcbass7 @ Jul 19, 2006 - 11:06...   Jul 19, 2006 - 6:51 PM
- - jcbass7   Ok well i cleared the codes and 12 went away now i...   Jul 20, 2006 - 9:06 AM
|- - phattyduck   QUOTE(jcbass7 @ Jul 20, 2006 - 7:06 ...   Jul 20, 2006 - 3:33 PM
|- - jcbass7   QUOTE(phattyduck @ Jul 20, 2006 - 3...   Jul 20, 2006 - 4:39 PM
- - Dr_Tweak   Okay so now it's cranking, but you have no sta...   Jul 20, 2006 - 4:47 PM
|- - jcbass7   QUOTE(Dr_Tweak @ Jul 20, 2006 - 4:47...   Jul 20, 2006 - 4:50 PM
- - jcbass7   ok ran a new wire and still getting code 22 (clear...   Jul 20, 2006 - 4:59 PM
- - Dr_Tweak   Is it plugged in? Does the brown wire have continu...   Jul 20, 2006 - 5:06 PM
- - jcbass7   ill check, brb one sec ok im not incredibly sure ...   Jul 20, 2006 - 5:10 PM
- - Dr_Tweak   Run a wire from the brown wire to a good ground an...   Jul 20, 2006 - 5:12 PM
- - jcbass7   ok i ran the ground, and now after clearing the co...   Jul 20, 2006 - 5:24 PM
- - Dr_Tweak   Okay, DO you have spark?   Jul 20, 2006 - 5:28 PM
- - jcbass7   Yes i do, i even got shocked checking it. I teste...   Jul 20, 2006 - 5:46 PM
- - Dr_Tweak   No, should be fine. Is your fuel pump running when...   Jul 20, 2006 - 5:51 PM
- - jcbass7   ok i beleive the wires are in the right order, 1...   Jul 22, 2006 - 6:32 PM
- - jcbass7   ok i AM getting fuel at the top of the fuel filter...   Jul 22, 2006 - 6:48 PM
- - jcbass7   ok so i ran the codes for the fun of it... now i...   Jul 22, 2006 - 7:15 PM
- - lagos   QUOTEok i beleive the wires are in the right order...   Jul 22, 2006 - 8:44 PM
|- - jcbass7   QUOTE(lagos @ Jul 22, 2006 - 8:44 PM...   Jul 22, 2006 - 8:53 PM
- - lagos   do you have your fuel injector resistor pack hooke...   Jul 22, 2006 - 10:20 PM
|- - jcbass7   QUOTE(lagos @ Jul 22, 2006 - 10:20 P...   Jul 23, 2006 - 8:24 AM
- - K-ESD   QUOTE(jcbass7 @ Jul 23, 2006 - 10:24...   Jul 23, 2006 - 8:39 AM
- - jcbass7   anywhere special? i have barely any slack on the c...   Jul 23, 2006 - 9:03 AM
|- - presure2   QUOTE(jcbass7 @ Jul 23, 2006 - 10:03...   Jul 23, 2006 - 9:55 AM
- - jcbass7   ok thats bolted down as well as the coil pack, now...   Jul 23, 2006 - 9:24 AM
- - jcbass7   is there a way i can test the injectors to see if ...   Jul 23, 2006 - 9:34 AM
- - jcbass7   currently a work in progress manny i moved the...   Jul 23, 2006 - 10:00 AM
- - lagos   QUOTEis there a way i can test these to see if the...   Jul 23, 2006 - 11:56 AM
- - phattyduck   Sounds like you also should check for power at the...   Jul 24, 2006 - 3:49 AM
- - jcbass7   You sure they need 12v with the key to the ON posi...   Jul 24, 2006 - 1:38 PM
- - jcbass7   ok i am getting no voltage on tkhe injectors when ...   Jul 25, 2006 - 8:36 AM
- - phattyduck   QUOTE(jcbass7 @ Jul 25, 2006 - 6:36 ...   Jul 25, 2006 - 12:50 PM


Reply to this topicStart new topic
46 User(s) are reading this topic (46 Guests and 0 Anonymous Users)
0 Members:

 



Lo-Fi Version Time is now: February 24th, 2025 - 11:29 AM