 3rd gen swap wont start |
 Jun 8, 2007 - 11:09 PM
|
 
|
 Enthusiast  Joined Apr 4, '05 From ST PAUL, MN Currently Offline Reputation: 3 (100%)  |
starter wont crank...just clicks from the inside.(of car).there seems as if there is no power going to the starter..wierd thing is that the radiator fan stays spinning.rechecked all wiring harness plugs and ground..starter wont crank over..checked starter today and it is working fine. please can anyone help with this problem....wiring harness was made by dr.tweak so i trust that it is fine..ooh yeah i did and have checked all the fuses like 30 times already even have one of my buddys do it like 10 times..everything is right...
This post has been edited by RUNNIN-LOW: Jun 8, 2007 - 11:26 PM --------------------  |
 |
Replies
|
Jun 18, 2007 - 9:36 PM
|
|
|
Enthusiast Joined Apr 4, '05 From ST PAUL, MN Currently Offline Reputation: 3 (100%) |
k well humm.. where do i get the (4th pic)injector resistor pack from would a thrid gen mr2 pack work??..and also do i even need the(5th pic) noise reducer coil to be plugged in anywas..ooh yeah i know where the starter plug goes but that was just to show yah my problem..i might just take my old start and rebuild it.anyone have aclue about the third picture.
-------------------- |
|
Jun 19, 2007 - 6:08 AM
|
|
|
Enthusiast Joined Mar 4, '06 From Ohio Currently Offline Reputation: 10 (100%) |
QUOTE(RUNNIN-LOW @ Jun 18, 2007 - 9:36 PM) [snapback]569850[/snapback] k well humm.. where do i get the (4th pic)injector resistor pack from would a thrid gen mr2 pack work??..and also do i even need the(5th pic) noise reducer coil to be plugged in anywas..ooh yeah i know where the starter plug goes but that was just to show yah my problem..i might just take my old start and rebuild it.anyone have aclue about the third picture. yea mr2 of the same generation would work. The third pic looks like a map sensor or cam position sensor. Look at the color of the wires and look in the wiring diagram. That may help. Also you can look at connectors in the ewd. I cant say for sure b/c my swap is a gen 2 |
Posts in this topic
RUNNIN-LOW 3rd gen swap wont start Jun 8, 2007 - 11:09 PM
OOBE Check the crank position sensor. On my Supra, the ... Jun 8, 2007 - 11:30 PM eggman40 Make sure all your grounds are good and are connec... Jun 9, 2007 - 5:05 AM toyotacrazy QUOTE(RUNNIN-LOW @ Jun 8, 2007 - 11... Jun 9, 2007 - 5:37 PM RUNNIN-LOW yes the enigine will turn over by hand..try that t... Jun 11, 2007 - 12:29 AM phattyduck Have you tried a different battery? The click is ... Jun 11, 2007 - 3:02 AM
toyotacrazy QUOTE(phattyduck @ Jun 11, 2007 - 3... Jun 11, 2007 - 5:23 AM
DSToyo QUOTE(phattyduck @ Jun 11, 2007 - 4... Jun 11, 2007 - 10:14 AM RUNNIN-LOW kk today i figure out or i think i did..good point... Jun 12, 2007 - 8:08 PM toyotacrazy QUOTE(RUNNIN-LOW @ Jun 12, 2007 - 8... Jun 12, 2007 - 11:03 PM scothaniel I had the single click when I had a bad ground (th... Jun 12, 2007 - 11:44 PM toyotacrazy QUOTE(scothaniel @ Jun 12, 2007 - 11... Jun 13, 2007 - 4:44 AM RUNNIN-LOW i didnt check that yet the circuit opening relay..... Jun 13, 2007 - 12:02 AM RUNNIN-LOW kk got pictures but havent loaded them up yet..but... Jun 17, 2007 - 10:40 PM scothaniel Do you have the injector resistor pack in? Do you ... Jun 18, 2007 - 12:40 AM toyotacrazy QUOTE(scothaniel @ Jun 18, 2007 - 12... Jun 18, 2007 - 6:24 PM RUNNIN-LOW These are the plugs that has no other plugs to plu... Jun 18, 2007 - 7:14 PM scothaniel Ok, it looks like you have some 3rd gen connectors... Jun 18, 2007 - 8:20 PM toyotacrazy QUOTE(scothaniel @ Jun 18, 2007 - 8... Jun 18, 2007 - 8:38 PM phattyduck QUOTE(RUNNIN-LOW @ Jun 18, 2007 - 7... Jun 19, 2007 - 1:26 PM scothaniel Let me check my old harnesses tomorrow - I may the... Jun 18, 2007 - 9:56 PM scothaniel I'm not sure what that 3rd pic is. It looks li... Jun 19, 2007 - 4:39 PM RUNNIN-LOW well if anyone can could they take pictures of the... Jun 19, 2007 - 6:17 PM eggman40 Ill have a pic up tomorow Jun 21, 2007 - 2:56 AM WannabeGT4 pic 2 looks kinda like it may be for the pressure ... Jun 21, 2007 - 7:12 AM scothaniel Pic 6 is definitely a 2nd gen injector resistor pa... Jun 21, 2007 - 10:29 AM WannabeGT4 QUOTE(scothaniel @ Jun 21, 2007 - 10... Jun 21, 2007 - 11:08 AM scothaniel Sorry man, I miscounted. I was looking at pic 7 wh... Jun 21, 2007 - 2:15 PM phattyduck QUOTE(scothaniel @ Jun 21, 2007 - 12... Jun 22, 2007 - 12:48 PM WannabeGT4 6 may very well be for a noise supressor but I don... Jun 21, 2007 - 4:26 PM RUNNIN-LOW thanks everyone for helping me out dame what would... Jun 22, 2007 - 7:37 PM laff09 QUOTE(RUNNIN-LOW @ Jun 22, 2007 - 7... Jun 22, 2007 - 11:54 PM 95WhiteOnWhite Doesnt look like any supermodel I ever seen Jun 23, 2007 - 11:46 AM shubert_ae102 its the sylinoid , my corolla did the same thing ,... Jun 24, 2007 - 12:21 AM RUNNIN-LOW well thanks to all that are tryin to help..thanks ... Jun 25, 2007 - 6:58 PM |
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: December 1st, 2024 - 2:19 AM |