Fabricated 6.5" Speaker mounts from the stock 8" front mount, Easy and free Options

[DEATH]

The the GF and I made up some speaker mounts for my Boston Acoustic SX60 6.5" component speakers. They came out really clean and the speakers sound incredible there. I figured I'd post a few pics so people who, like me don't care to wait/pay for adapters, can see how we did it. All pics are from driver's side door panel but the passenger is the same:
1. Start by removing the door panel [Not going to go into specifics on this as it's super easy and covered in your Chilton's or Hayne's manual]. Pics of the speaker housing with the door off:

2. Disconnect the white wire connector located at the top of the speaker housing [Driver's side will have 1 pink and 1 purple-ish wire as shown above]. Remove the four 12mm screws [2 top, 2btm] holding the speaker housing in place. You will be left with this:

and this:

3. Next we continued by ripping out the original speaker cones [no pics of that - it's pretty self explanatory].
4. We cut the magnets and posts mounting them to the original speaker rings out with a dremil tool. This part was easy and only took about 30mins each to get them off and the edges nice and smooth with a sanding wheel on the dremil. Make sure your new speaker cone will drop in without rubbing or ripping on the cut edges [a smooth finish is not necessary if you are careful when mounting the new speaker - I, however, like to do things right and take my time - to a fault probably]
*Pic missing - I will get it up soon*
5. Next we drilled 3 holes using the speaker as a guide. This will vary with the speakers - some have 3 mounting holes, some have 4 mounting holes. Just be careful and only use your speaker to mark it with - Don't drill with the speaker attached so you don't risk drilling a hole through the cone .
*Pic missing - I will get it up soon*
6. Attach your new speaker to your custom made speaker adapter using screws and nuts on the back and add the bezil if you wish [not necessary but again I decided why not?]:

Be sure the magnet does not extend farther out than the stock enclosure will allow [the window will be obstructed if your magnet extends any farther]:

with the bezil [Mine somehow magically snapped into place inside the stock ring but I used the included mounting hardware as well - follow manufacturers instructions on this step]:

7. Next i drilled a hole in the housing to run the speaker thru and since they are not sealed enclosures I did not bother to seal them up [mainly cause I couldn't find my silicone ]. You can see the wires run thru two pics above.
8. This step will be different for several different setups. I chose component speakers so I ran the stock wires to the input of the included crossovers [you will just splice them into your new speaker's wires if you choose to use full range speakers - pretty self explanatory]. I then ran the "woofer" output from the crossover to the new 6.5"s and ran a length of wire from the "tweeter" output to be used later and mounted the crossover to the enclosure [this is a perfect example of where not to mount the crossover on the driver's side. This is exactly where the window controls sit - I figured this out as I was installing the last peice of my door panel - the controls . This is a great example of where to mount them for the passenger side (in other words you need a mirror image of this setup for the driver's side door]:


9. Decide where to mount your tweets if component - skip to step 10 if full range. I have not yet decided where to mount my tweets as I still wish to retain the stock tweets as well - the stock bracket is not setup to accept aftermarket tweets and I want to end up with 6 tweets total when I'm done so this is how I did mine.
10. Remount the door panel [route the tweet wire if necessary]. Everything looks stock now as shown:

even in close up:

Notice in the first pic you can see where I left the tweet wire poking through bottom corner of the door for future use [Nevermind the boost gauge line and the gauge wires running to the right - it's a swapped car and I'm not done with my gauge setup so leave me alone damn it ]. In the end I'm leaning towards installing them just to the rear of the speaker in that traingular dead space between the speaker and the door pocket. Most manufacturers of component speakers will give you an acceptable radius of where to mount the tweets relative to the 6.5"s to achieve the best sound - listen to them, they are the experts on sound imaging. You may also choose to cut out the stock grill so that you can see the aftermarket speaker grill - this would be very easy to do with the same dremil you used in step 4 [I live in Houston Tx and that's a good way to get your speakers stolen and a window busted so I opted for the "sleeper" look ].
11. Crank it up and enjoy

Mods feel free to add to the stickys or how-to's - I would be honored .
Stay tuned for more how-to's as my system is installed [BTW - I installed my Rockford-Fosgate 6.5" components in the rear for now - I may make a how-to on that as well]. Please don't reply with a copy of all this info - many how-to's get muddied this way. If you have a specific question on a step or pic feel free to reply with that tho. Thanks in advance.

This post has been edited by DEATH: Apr 1, 2008 - 4:08 PM

[DEATH]

what are you going to do in the back speaker-wise?? Are you doing the 1: 15 you was showin me, or 2 with a new box?
you got the hatch, i say you go all out, you have the compression potential. You already know i'll help you build some schett!! I'll do ya some glass work if you can find us a place to do the toxic work.

The one 15". Been there done that with the (2) 15"s and absolutely no cargo space - not necessary. With the right 15" and the right tuning you can make any airspace sound perfect. Besides I'm not trying to weigh the car down - I'm trying to go fast with some decent tunes. This car will never be an audio queen.
As for FG work - you'll be doing something cool in this trunk - just as soon as I figure out how to lay out the two amps, crossovers and capacitor.

once i get what i ordered, i will give you a part number if you like, then youll setup will be complete...

???

[D-Man]

As for FG work - you'll be doing something cool in this trunk

okay