 Greddy Profec B Spec-II settings |
 Jun 1, 2009 - 10:58 PM
|
 
|
 Enthusiast  Joined Mar 11, '09 From Baltimore, Maryland Currently Offline Reputation: 1 (100%)  |
I just installed a Greddy Profec B Spec-II
 I need some help tuning the new toy. I have a 3s-gte so 12psi is the max I should run.10psi= 68kPa 11psi= 75kPa 12psi= 82kPa 13psi= 89kPa Boost Mode Lo Set 38% Gain 10% Start Boost 0.65 (x100kPa) (range:0~3.0 x x100kPa) Warning 0.75 (x100kPa) Limiter L.20% Boost Mode Hi Set 42% Gain 15% Start Boost 0.75 (x100kPa) Warning 0.82 (x100kPa) Limiter L.30% I'm not sure about any of the settings. Are there any stickys on this? This post has been edited by speed-CCNP: Jun 1, 2009 - 10:59 PM |
 |
Replies
|
Jun 2, 2009 - 7:00 PM
|
|
 Enthusiast Joined Aug 31, '02 From Philadelphia, PA Currently Offline Reputation: 8 (100%) |
No thats not too much boost, as long as you have a front mount intercooler.
-------------------- 15PSI - 30MPG - Megasquirt Tuned
|
Posts in this topic
speed-CCNP Greddy Profec B Spec-II settings Jun 1, 2009 - 10:58 PM
lagos Every car is different, but here is the basic idea... Jun 1, 2009 - 11:24 PM
speed-CCNP Thanks, I think i got it. But 1.0 bar is equal to ... Jun 2, 2009 - 6:44 PM speed-CCNP I still have the stock top mount IC on the car. I... Jun 3, 2009 - 9:10 PM lagos You will blow your motor if you keep that air to a... Jun 3, 2009 - 9:17 PM speed-CCNP don't want to kill the motor!!!
w... Jun 3, 2009 - 10:12 PM Defgeph I have been trying to figure out how to properly s... Jun 3, 2009 - 10:25 PM presure2 QUOTE (Defgeph @ Jun 3, 2009 - 10:25... Jun 4, 2009 - 5:56 AM Defgeph QUOTE (presure2 @ Jun 4, 2009 - 6:56... Jun 4, 2009 - 11:30 AM presure2 RE: Greddy Profec B Spec-II settings Jun 4, 2009 - 11:36 AM Defgeph FU Jun 4, 2009 - 11:41 AM DEATH I gotta get me one of these toys
OP - Art is rig... Jun 4, 2009 - 3:24 PM speed-CCNP Thanks. I plan to put the FMIC on tomorrow. Jun 6, 2009 - 8:44 PM speed-CCNP i plan to use the clamps but I was told I should h... Jun 6, 2009 - 9:14 PM lagos QUOTE (speed-CCNP @ Jun 6, 2009 - 1... Jun 6, 2009 - 11:17 PM presure2 welding most of the pipes is best, but you will st... Jun 7, 2009 - 8:08 AM |
3 User(s) are reading this topic (3 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: February 21st, 2025 - 3:29 PM |