 engine problem after rebuild, wont start and run |
 Apr 23, 2010 - 10:48 PM
|
 
|
 Enthusiast  Joined Aug 4, '05 From Ocala Fl Currently Offline Reputation: 0 (0%)  |
alright well here is the story. i bought a 97 celica vert for 150 bucks and the engine that was in it threw a rod. so needless to say it was no good. i pulled the engine and got another 2.2 out of a camary. i turned the crank, new rings, valve seals the whole 9. anyways i but the damn thing back in and tried to start her but she will not run. the motor is in time check in 4-5 times, i got spark, fuel, and cmpression is about 155-160 in each cylinder. ive tried replacing the crank sensor, tps, i put in a new injectors off another motor i had. each cylinder is getting fuel cause the plugs are wet. the only thing i havent checked yet is the fuel pressure, but i know its getting up there. the only thing the motor doesnt have now is the egr and all the hose that went along with it. all my grounds are hooked up and ive even added a few. i just need some advice on what this could be, i am stumped. thanks in advance.
-------------------- 1997 Celica Convertible (going to rebuild again)
1994 TT 6Spd Supra 1969 Camaro 1997 S-10 1997 Astro Van |
 |
Replies
|
Apr 23, 2010 - 10:59 PM
|
|
 Enthusiast Joined Oct 10, '06 From Greensburg,PA Currently Offline Reputation: 27 (94%) |
define will not run... thats pretty broad... it chokes? it starts and dies? it doesn't turn over? it turns but doesn't fire? be more specific... its the only way we can help
-------------------- Breaking Axles...
|
Posts in this topic
STCelica engine problem after rebuild Apr 23, 2010 - 10:48 PM
STCelica just cranks over, its cranking but will not fire. ... Apr 23, 2010 - 11:10 PM
pittfirefighter QUOTE (STCelica @ Apr 23, 2010 - 11... Apr 23, 2010 - 11:17 PM STCelica the firing order is good and i know i have spark n... Apr 23, 2010 - 11:26 PM Bitter ignition timing way off? Apr 23, 2010 - 11:28 PM STCelica used a timing light and it flashed that it was on ... Apr 23, 2010 - 11:33 PM Bitter what year was the camry? what parts off the camry ... Apr 24, 2010 - 10:34 AM Smaay well if your compression is that good timing shoul... Apr 24, 2010 - 11:23 AM STCelica Think it was a 93. As far as parts go I used every... Apr 24, 2010 - 1:37 PM Bitter well you're missing something, are the injecto... Apr 24, 2010 - 2:04 PM STCelica Yep I took the rail off the old motor and put it o... Apr 24, 2010 - 8:09 PM stephen_lee try swappin the wires between cyl 1/4 and 2/3
your... Apr 25, 2010 - 5:58 PM STCelica well another day done and still cant get this #@%... Apr 27, 2010 - 10:08 PM Motegi QUOTE (STCelica @ Apr 23, 2010 - 10... Apr 28, 2010 - 3:18 AM STCelica Well I'll ohm test the dist before I buy a new... Apr 28, 2010 - 8:17 AM STCelica Also wheni hooked it up to a obdII reader it pulle... Apr 28, 2010 - 8:28 AM STCelica Now I just called a guy who has Micheal on demand ... Apr 28, 2010 - 10:43 AM bmj67 Dont use a timing light to set physical timing of ... Apr 28, 2010 - 11:48 AM CELL_PROTOTYPE_X Did you check your fuel pump? Apr 28, 2010 - 12:20 PM STCelica I know the pump is good since Im getting good psi.... Apr 28, 2010 - 1:14 PM csscza Im rebuilding a 95 GT right now and Im following a... Apr 28, 2010 - 1:41 PM STCelica Today my dad tested the fuel pressure regulator an... Apr 29, 2010 - 6:57 PM STCelica Well good news. IT'S ALIVE. I got tge damn thi... May 4, 2010 - 7:16 PM Bitter a compression test would have saved you alot of ti... May 4, 2010 - 7:47 PM STCelica Yeah I did a compression check and it read 160 psi... May 4, 2010 - 9:04 PM Bitter thats weird that you'd have compression then, ... May 4, 2010 - 11:11 PM csscza good job Im looking at putting a head on today and... May 5, 2010 - 7:55 AM STCelica The dist runs off the intake cam. And as far as th... May 5, 2010 - 10:24 AM Bitter intake, exhaust whatever they're both soo clo... May 5, 2010 - 7:42 PM STCelica lol gottcha ill let it slide this time, but next t... May 5, 2010 - 9:43 PM |
3 User(s) are reading this topic (3 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: November 23rd, 2024 - 10:05 AM |