 Basic how to/walk through on Removing the Transmisson, reference thread for people |
 Jun 29, 2009 - 4:20 AM
|
 
|
 Enthusiast  Joined Feb 24, '07 From Oahu, Hawaii Currently Offline Reputation: 23 (100%)  |
gonna set up this thread before i foget. I'll be pulling the trans and everything else with it so people car use this, or not, as reference to removing axles, starter, and transmission.
not gonna be a perfect thread but it should do. -unhook battery -remove cruise control when applicable -remove starter  -unhook shifter cables  -remove slave from trans  -drain tranny -remove axles          remove speed sensor -----its behind the shifter cables just unhook it like the back up light -remove backup light sensor  -remove center cross member  -remove front mount   -remove rear mount   -support engine, unbolt trans mount   -support trans   -lowering trans    -remove Pressure plate, disk, bearing        -remove fork (cuz im replacing mines) it just pulls right out  Installation is reverse sorry i didnt get pics i was doing this part by myself This post has been edited by 808celica: Jun 17, 2010 - 9:48 PM -------------------- I don't normally drive fast, but when I do its on a curvy section of this island
 |
 |
Replies
|
Jun 17, 2010 - 9:46 PM
|
|
|
Enthusiast Joined Feb 24, '07 From Oahu, Hawaii Currently Offline Reputation: 23 (100%) |
he's talking about the strut bolts
-------------------- I don't normally drive fast, but when I do its on a curvy section of this island
|
Posts in this topic
808celica Basic how to/walk through on Removing the Transmisson Jun 29, 2009 - 4:20 AM
808celica pics are up of some stuff. those who are removing ... Jun 30, 2009 - 9:24 PM lagos VERY COOL!
btw, you dont need to remove your h... Jun 30, 2009 - 10:32 PM
808celica QUOTE (lagos @ Jun 30, 2009 - 5:32 P... Jul 1, 2009 - 5:25 AM
KAOS QUOTE (lagos @ Jun 30, 2009 - 9:32 P... Jun 11, 2010 - 9:43 AM ksporry Sorry, I'd like to use this as a guide to repl... Jul 1, 2009 - 6:49 AM presure2 QUOTE (ksporry @ Jul 1, 2009 - 6:49 ... Jul 1, 2009 - 6:59 AM 808celica QUOTE (ksporry @ Jul 1, 2009 - 1:49 ... Jul 1, 2009 - 4:17 PM dgbldr Once you get to that point, where the engine and t... Jul 1, 2009 - 11:17 AM presure2 QUOTE (dgbldr @ Jul 1, 2009 - 11:17 ... Jul 1, 2009 - 11:25 AM GriffGirl QUOTE (presure2 @ Jul 1, 2009 - 9:25... Jul 1, 2009 - 3:22 PM dgbldr QUOTE (presure2 @ Jul 1, 2009 - 12:2... Jul 1, 2009 - 10:03 PM presure2 QUOTE (dgbldr @ Jul 1, 2009 - 10:03 ... Jul 2, 2009 - 6:26 AM 808celica QUOTE (dgbldr @ Jul 1, 2009 - 5:03 P... Jul 4, 2009 - 1:02 AM lagos QUOTE (808celica @ Jul 1, 2009 - 6:2... Jul 1, 2009 - 12:02 PM Mstoochn folowed this guide for my auto to man swap. Jul 1, 2009 - 4:45 PM presure2 QUOTE Then use a engine crane/cherry picker/transm... Jul 1, 2009 - 5:24 PM njccmd2002 QUOTE (presure2 @ Jul 1, 2009 - 6:24... Jul 1, 2009 - 5:38 PM presure2 QUOTE (njccmd2002 @ Jul 1, 2009 - 5... Jul 1, 2009 - 5:41 PM 808celica QUOTE (presure2 @ Jul 1, 2009 - 12:2... Jul 1, 2009 - 8:08 PM 808celica Oh i read your question right I doubt the pressur... Jul 2, 2009 - 4:56 AM 808celica if i dont get caught up ripping everything apart i... Jul 2, 2009 - 12:29 PM 808celica dONE!! putting the motor was a PITA!... Jul 3, 2009 - 6:34 PM cardshark525 Well I'm glad I found this thread. Just my ... Nov 10, 2009 - 11:08 PM 808celica Wow you dug this up Hahah Now that's using the... Nov 12, 2009 - 9:42 PM cardshark525 QUOTE (808celica @ Nov 12, 2009 - 10... Nov 17, 2009 - 9:34 PM 808celica QUOTE (cardshark525 @ Nov 17, 2009 - 4... Nov 17, 2009 - 10:01 PM epocsirhc I've never done a clutch but axles are easy. I... Nov 17, 2009 - 9:52 PM cardshark525 I've got another question as we're nearing... Nov 19, 2009 - 12:41 AM 808celica QUOTE (cardshark525 @ Nov 18, 2009 - 7... Nov 19, 2009 - 3:29 AM KAOS QUOTE (808celica @ Jun 17, 2010 - 8... Jun 17, 2010 - 10:16 PM Smaay this is a good thread, good pics. thumbs up!... Jun 17, 2010 - 10:14 PM |
6 User(s) are reading this topic (6 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: November 26th, 2024 - 10:53 PM |