FS: '94 GTS with 3SGTE swap partout!, Everything must go, cheap! More Items Added, 5SFE parts too! |
FS: '94 GTS with 3SGTE swap partout!, Everything must go, cheap! More Items Added, 5SFE parts too! |
May 4, 2011 - 10:11 AM |
|
Enthusiast Joined Sep 20, '09 From Cambridge, Ontario Currently Offline Reputation: 1 (100%) |
Unfortunately I ran out of money for my project so I decided to part it out. These are the parts I have left and i need to sell everything so everything is obo.
Buyer pays shipping. Email for pictures please! 3SGTE ECU and harness ( harness is missing the clip for the fuel pump resistor pack, so the wires have been taped together and marked.) $125 for both or $65 each 3SGTE Ignitor and coil - $40 3SGTE Intake box and pipe - SOLD GT front seats (good condition-cloth) - SOLD Rear seats (good condition) - $30 2 sets of usdm taillights (good condition) - $20 each side doors (black, good condition, everything works but i very slight bit of rust at the bottom) - SOLD rear hatch (great condition everything works, black, no spoiler or interior pieces) $100 aluminum radiator with fans (trimmed to fit already and don't know make.) - SOLD GT shifter and shifter cables - $40 Random interior pieces (speakers, center arm rest, glove box, center console trim pieces, gauge cluster, ac controls) - SOLD hood latch and brand new cable - $30 3s pressure plate (good condition) - $50 5sfe greddy stage 2 clutch plate (like new great condition) - $75 Cross drilled front rotors and brand new rear rotors (never used) - $50 Power steering reservoir, windsheild washer reservoir (with pump), engine coolant reservoir - $ 30 for all 5sfe ecu - $40 Ebrake lever (good condition) - $15 Front and rear bumper (good condition, few scratches) - $50 for both Exoticspeed titan t1 muffler 3" inlet 4" outlet, silencer included (bnib) and yonaka high flow cat 3" inlet and outlet - $225 for both Im trying not to ship the doors and hatch because of their size, so i will be able to meet some where for you to pick them up. Thanks, Matt This post has been edited by spydercon: May 31, 2011 - 8:24 AM |
Jun 10, 2011 - 8:53 AM |
|
Enthusiast Joined Sep 20, '09 From Cambridge, Ontario Currently Offline Reputation: 1 (100%) |
its a gen 3 and currently i do have a buyer but I will let you know if it falls through.
|
Jun 10, 2011 - 1:43 PM |
|
Enthusiast Joined May 13, '06 From Kaimuki, HI Currently Offline Reputation: 10 (100%) |
its a gen 3 and currently i do have a buyer but I will let you know if it falls through. k, the parts I need are things that you would be stuck with after a part out anyway, so you would probably sell most of it if you did part it out. Let me know, thanks. -------------------- -Jay
95 GT conv. project car: Manual, Gen III 3sgte, JN pisons, Eagle rods, overbore, crank knife-edged, crank scraper, ARP head/main/flywheel, Autronic EMS, Haltech Dual Wideband O2 controller, Audi 1.8T individual coils, FMIC and SSQV BOV, 3" downpipe, 3" ultra-high-flow cat, 2.5" Borla muffler, +other 01 S2000: FMIC, Haltech EMS, Haltech wideband, 570cc inj, forged pistons/rods, sleeved block, 5 angle valve job, ported and polished 02 R6, all stock, except for braided stainless brake lines, frame sliders, and adjustable brake/clutch leve |
Lo-Fi Version | Time is now: November 26th, 2024 - 6:35 AM |