Test fit of my custom lamps. Halo Projectors, Finished on Page 4 Options

[yellowchinaman]

Use a little imagination here


today I marked up how much I need to trim off the fender bottom edge and also the tubular part of the lamp on the bumper.
The idea is I wont need the middle lamps so I can have 1 as a air intake and the other to be flushed out.
The fitting of these lamps will be more aerodynamic than the stock ones and best of all, these are clear lense and have projector halos in them B)

This post has been edited by yellowchinaman: Jan 6, 2014 - 3:11 PM

[mandrek]

thank you!!! yellowchinaman. yeah after looking at this thread, i reconised your name and profile pic, and was like " wait, i just read a thread w/ him talking about making some realy cool arow part for the front under tray" then looked you up on 6gc here, when i seen all of your threads about the TOP NOTCH replicas and 100% fit.. i was like "DAMN!!!! why do you have to be all the way over in london, and me poor!!" lol.. all that to say that after reading this i looked you up and seen all of the cool stuff you make and have made availible to us here on 6gc, and noticed the "wings" .. oh and was trolling ebay last night too (after seeing this) and i think i would go with this set

upon further inspection of your OP pic i would think that you would be able to fit it w/o having to remove anything from the front quarters. (as you are now considering) im hopeing that this is true, as i have the factory metal ones.
how are you planning to hook up the additional lights? looks like that top section is for oem turn signal? (in the neon) perhaps put our turns up there too (w/ LED "bulbs", nice since when they are off they are clear/white, so they dont leave an orange reflection in the housing) and give us our OEM section as a new vent or to block off/fill in.
as far as the LED's and halo' i was thinkinig of just having those on a switch, or perhaps even having the LEDs as turn... hmm idk, so many difrent options with this..

[yellowchinaman]

thank you!!! yellowchinaman. yeah after looking at this thread, i reconised your name and profile pic, and was like " wait, i just read a thread w/ him talking about making some realy cool arow part for the front under tray" then looked you up on 6gc here, when i seen all of your threads about the TOP NOTCH replicas and 100% fit.. i was like "DAMN!!!! why do you have to be all the way over in london, and me poor!!" lol.. all that to say that after reading this i looked you up and seen all of the cool stuff you make and have made availible to us here on 6gc, and noticed the "wings" .. oh and was trolling ebay last night too (after seeing this) and i think i would go with this set

upon further inspection of your OP pic i would think that you would be able to fit it w/o having to remove anything from the front quarters. (as you are now considering) im hopeing that this is true, as i have the factory metal ones.
how are you planning to hook up the additional lights? looks like that top section is for oem turn signal? (in the neon) perhaps put our turns up there too (w/ LED "bulbs", nice since when they are off they are clear/white, so they dont leave an orange reflection in the housing) and give us our OEM section as a new vent or to block off/fill in.
as far as the LED's and halo' i was thinkinig of just having those on a switch, or perhaps even having the LEDs as turn... hmm idk, so many difrent options with this..

Thanks for the compliments.
I'll keep this updated whenever I do get a chance to do more work on it but that doesn't happen often as we have a workshop to run and we don't get much time to do our own things.
Regarding the stock turns I may just mesh it out. But then again I have a Varis front and I'm trying to make the car as aerodynamically better so having them as vents wont really help.