 3s-gte rebuild |
 Oct 6, 2011 - 3:41 PM
|
 
|
|
Enthusiast  Joined Nov 2, '06 From Finland Currently Offline Reputation: 0 (0%)  |
Hello!
I got 1994 st205 celica. now it's time to rebuild the engine. it started knock very bad. i think it's camshaft bearings. The knock started when i was driving, i stop and the oil was wery low. I need advice where to buy new parts. i'm from Finland. I got the engine out and now i have a problem. i can't get the trans off the engine. i think every bolt is off. help please! here is some pictures intake side  exhaust side 
|
 |
Replies
|
Oct 21, 2011 - 5:58 PM
|
|
|
Enthusiast Joined May 16, '10 From Raleigh Currently Offline Reputation: 12 (100%) |
you may be looking at a new crank sir...if i'm seeing what i'm seeing in this image. looks like the journal is torn up pretty bad...Some closer pictures would be advantageous.
--------------------  |
Posts in this topic
Gt4Driver 3s-gte rebuild Oct 6, 2011 - 3:41 PM
bsamps4 Problem #1
Your starter is still attached to the ... Oct 6, 2011 - 7:16 PM Neon90424 www.ebay.co.uk should have sellers that sell to eu... Oct 6, 2011 - 10:18 PM Gt4Driver Ok. thanks guys.
need to remove the starter. then ... Oct 7, 2011 - 12:27 AM
malpaso QUOTE (Gt4Driver @ Oct 7, 2011 - 7:2... Oct 7, 2011 - 4:30 AM Rav4Race i use to get my parts in malaysia. Always the best... Oct 7, 2011 - 6:22 AM Gt4Driver Today i got the trans off Oct 10, 2011 - 1:50 PM Neon90424 looks like a clutch kit could do good for you...th... Oct 10, 2011 - 3:12 PM Gt4Driver Yes it looks like it's time to chance it is t... Oct 10, 2011 - 11:50 PM Neon90424 they are the same I believe Oct 11, 2011 - 6:40 AM Sunny Hi,
a short list of which parts you are seaching ... Oct 11, 2011 - 8:03 AM Gt4Driver Hi. I need new clutch, main and rod bearings, bott... Oct 11, 2011 - 10:50 AM Sunny Hi,
get the parts from toyota, here a link that h... Oct 11, 2011 - 12:50 PM Gt4Driver well. i think the bearings are bad, cause i was lo... Oct 11, 2011 - 1:13 PM Sunny Hi,
do not try to safe money, this can couse the ... Oct 11, 2011 - 4:12 PM Smaay the knock is defiantly from the crank bearings. th... Oct 11, 2011 - 5:17 PM Gt4Driver hello. it seems to be my 3 cylinder rod bearing is... Oct 16, 2011 - 11:04 AM Neon90424 they sell all 4 together and its not that expensiv... Oct 16, 2011 - 12:51 PM bsamps4 It would be crazy to not replace all bearings... Oct 16, 2011 - 3:50 PM Gt4Driver ok. So im gonna replace all bearings.
In toyodiy ... Oct 17, 2011 - 1:54 PM Neon90424 the std, .025 etc are in case you have spun a be... Oct 17, 2011 - 4:44 PM bsamps4 Take caution. You need to have your crank journals... Oct 17, 2011 - 7:58 PM Mr_Tee QUOTE (bsamps4 @ Oct 17, 2011 - 7:58... Oct 23, 2011 - 2:27 AM Gt4Driver RE: 3s-gte rebuild Oct 21, 2011 - 4:30 PM Gt4Driver what do you think about this? Do i need a new cran... Oct 23, 2011 - 7:47 AM enderswift that doesn't look bad. You're really only ... Oct 23, 2011 - 7:15 PM bsamps4 The close up picture looks a lot better than the o... Oct 24, 2011 - 7:21 PM Gt4Driver Ok. the car was running great before the bearing ... Oct 24, 2011 - 11:37 PM bsamps4 You need to have the crank machined first and ask ... Oct 25, 2011 - 12:22 PM Gt4Driver Hello!
Got the crank back from machineshop, st... Nov 4, 2011 - 2:30 AM bsamps4 Sounds great! Did you put new rings on the pis... Nov 4, 2011 - 10:12 AM Gt4Driver Old rings and pistons. Nov 4, 2011 - 10:27 AM bsamps4 If you're running the old rings make sure to c... Nov 7, 2011 - 11:22 AM Gt4Driver put the engine in today Nov 13, 2011 - 7:34 AM Neon90424 RE: 3s-gte rebuild Nov 13, 2011 - 10:11 AM Gt4Driver Few pics Nov 13, 2011 - 1:46 PM bsamps4 Great pics man! Hope it runs as good as it loo... Nov 14, 2011 - 9:13 AM Gt4Driver Little progress Nov 15, 2011 - 4:42 AM Gt4Driver Ok. one question. My timing belt side driveshaft w... Nov 15, 2011 - 7:12 AM bsamps4 No, it needs to click in all the way. The transmis... Nov 15, 2011 - 9:36 AM Gt4Driver So do i just need to hammer it on?
The other side ... Nov 15, 2011 - 9:42 AM rave2n I had to tap mine in with a deadblow to an end of ... Nov 15, 2011 - 2:42 PM Gt4Driver Oil sanwich plate install for oil pressure gauge a... Nov 15, 2011 - 3:51 PM Neon90424 my mechanic was preocupied by the oil press sensor... Nov 15, 2011 - 4:21 PM Gt4Driver Thanks for warning. i'll check that Nov 16, 2011 - 1:05 AM Gt4Driver That fu***** driveshaft wont go in.
Been hammer... Nov 16, 2011 - 3:41 PM bsamps4 Any way you could pull it out and take a pick of w... Nov 16, 2011 - 4:06 PM Gt4Driver Ok. i'll take a pick tomorrow, now i need to g... Nov 16, 2011 - 4:14 PM Gt4Driver it's in! just take it off and put it back.... Nov 17, 2011 - 4:49 PM Gt4Driver Ok. It's time to fire it up Hope everything... Nov 20, 2011 - 4:19 AM Gt4Driver No it wont start. starter just klicks. Nov 20, 2011 - 7:54 AM Gt4Driver I hammered my starter and it starts to work Nov 20, 2011 - 9:33 AM Neon90424 sounds like a new starter is in order... Nov 20, 2011 - 9:44 AM Gt4Driver Yes i think so. but it works now. Engine runs grea... Nov 20, 2011 - 11:20 AM |
5 User(s) are reading this topic (5 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: November 27th, 2024 - 6:35 AM |