 exhaust header, surewinproducts negative comments |
 Mar 1, 2012 - 12:38 PM
|
 
|
|
Enthusiast Joined May 31, '11 From Tucson Currently Offline Reputation: 0 (0%)  |
i am ready to update my exhaust system starting with the header and see several negative posts about surewinproducts. these were not posted on 6g but come up with a search for surewinproducts.
lots of other people selling headers for a 94 celica gt if 6g peolple have problems with surewinproducts please let me know plbmc2 |
 |
Replies
|
Mar 1, 2012 - 1:13 PM
|
|
 Enthusiast  Joined May 4, '05 From western MD/NOVA Currently Offline Reputation: 2 (100%) |
i assume that you are referring to an E-bay header? one of the many on there.. i don't want to be an ass , but the simplest thing to say is to expect to get what you pay for.. as long as you are ok and understand that.. then the rest is cake.. i got an E-bat header for my 91MR2 (5sfe) for something like $45.. stupid low.. i knew that it would not be the best but for the cost, who cared as long as it "fit"... got it.. the flange was flat (not warped at all) on any of em. the ports lined up, and the holes for the bolt lined up too... great right?!?!?! well had a nasty backfire during an auto-x with it, and the damn O2 bung blew right off!!!.. ****ty SS, and welds.. not a problem, i just welded it back on with ma'MIG (even though it was just regular steel wire) slobbed some additional gasket sealer (the grey stuff that is water clean up when wet, but dries hard as a rock, from advanced exhaust section) on the flange for the bung (in-case my welds warped the flange even a bit) and have not had any more problems with it ever since!!!! i got lucky though.. some of those $45 ones are trash.. got a similar priced one off ebay for my 7a and ALL the holes drilled for the studs on the manifold-to-head flange were off to the right by about 1/2 an inch.. $45 worth of scrap metal.. (but i WILL still use it, one way or another)
good luck -------------------- |
|
Mar 1, 2012 - 9:39 PM
|
|
 Enthusiast Joined Oct 17, '11 From Kent, WA Currently Offline Reputation: 0 (0%) |
QUOTE (mandrek @ Mar 1, 2012 - 1:13 PM)  i assume that you are referring to an E-bay header? one of the many on there.. i don't want to be an ass , but the simplest thing to say is to expect to get what you pay for.. as long as you are ok and understand that.. then the rest is cake.. i got an E-bat header for my 91MR2 (5sfe) for something like $45.. stupid low.. i knew that it would not be the best but for the cost, who cared as long as it "fit"... got it.. the flange was flat (not warped at all) on any of em. the ports lined up, and the holes for the bolt lined up too... great right?!?!?! well had a nasty backfire during an auto-x with it, and the damn O2 bung blew right off!!!.. ****ty SS, and welds.. not a problem, i just welded it back on with ma'MIG (even though it was just regular steel wire) slobbed some additional gasket sealer (the grey stuff that is water clean up when wet, but dries hard as a rock, from advanced exhaust section) on the flange for the bung (in-case my welds warped the flange even a bit) and have not had any more problems with it ever since!!!! i got lucky though.. some of those $45 ones are trash.. got a similar priced one off ebay for my 7a and ALL the holes drilled for the studs on the manifold-to-head flange were off to the right by about 1/2 an inch.. $45 worth of scrap metal.. (but i WILL still use it, one way or another) good luck i dont mean to be a dick but if ALL the wholes where off a 1/2inch to the right couldnt you just move it a quarter of an inch? |
Posts in this topic
plbmc2 exhaust header Mar 1, 2012 - 12:38 PM
mandrek QUOTE (TannerEsser @ Mar 1, 2012 - 9... Mar 1, 2012 - 9:46 PM
Spider77 The only problem I had with the Surewin header are... Mar 1, 2012 - 2:03 PM Smaay i wrote a thread on the surewin header. just searc... Mar 1, 2012 - 3:31 PM UVZ164 As far as i knew surewinproducts had stopped makin... Mar 1, 2012 - 8:58 PM plbmc2 QUOTE (UVZ164 @ Mar 1, 2012 - 9:58 P... Mar 1, 2012 - 9:41 PM |
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: November 24th, 2024 - 1:21 AM |