 Clutch Master Cylinder, Which one is it? |
 Feb 14, 2012 - 5:47 PM
|
 
|
 Enthusiast  Joined Aug 2, '05 From Guam Currently Offline Reputation: 15 (100%)  |
Are there two types of clutch master cylinders for my 94 2.2L Celica GT? I converted my car to manual back in 2009 and my generic clutch master brand is about to give out. I'm running 3sgte light flywheel and clutch from Competition Clutch. sometimes it gets stuck and i have to pick it up by hand and pump it, fluid is slightly lower than full, and fluid is hella dirty, looks like an internal seal leak to me. Plan to buy an OEM one. I've seen online on toyota sites - two kinds of masters though, 1 that goes up with a long neck reservoir (i have this type) and the other one looks like a typical one with a long cylinder and stubby reservoir. I cannot just put my VIN in because my VIN is for automatic. so when I use toyodiy for the part number i get the stubby one on the toyota site, I want to be sure what I'm getting because I do not know for sure if thats just an illustration because i have the longer neck type. BTW, I've also seen the stubby ones as well for sale so thats why i think there are two.
Are there any performance clutch master cylinder and slave for our cars? This post has been edited by trdproven: Feb 14, 2012 - 5:49 PM -------------------- 94 Celica GT
|Toyota OEM Japan|Toyota Racing Development|Tom's|Competition Clutch|5Zigen|Apexi| |Laille/Beatrush|Magnecor|Denso|Royal Purple|Optima|PIAA|PW JDM|Megan Racing|Nitto| |Work|Greddy|Samco|Project Mu|H&R|Gates|Moog|Rota|Yokohama|Epman|1320|Upgr8 04 Celica GT |Toyota OEM Japan|Toyota Racing Development|Tein|BC Racing|Greddy| |
 |
Replies
|
Apr 18, 2012 - 10:46 AM
|
|
|
Enthusiast Joined May 29, '09 From Gainesville, FL Currently Offline Reputation: 17 (100%) |
Yea you got a leak after looking at that video.
Could be leaking within the slave, master, or one of your lines. I would start with the slave, its a 15 dollar part at autozone, change it out..see what happens. Or check for some obvious fluid loss around all the soft and hard lines. This post has been edited by rave2n: Apr 18, 2012 - 10:47 AM |
Posts in this topic
trdproven Clutch Master Cylinder Feb 14, 2012 - 5:47 PM
Smaay performance? none that i know of. as far as i know... Feb 14, 2012 - 5:57 PM azian_advanced i know the ones with the long neck are for LHD and... Feb 14, 2012 - 6:15 PM rave2n If its the GT its the long neck atleast here in US... Feb 14, 2012 - 6:40 PM trdproven ok so the toyota site is just for illustration pur... Feb 14, 2012 - 7:23 PM trdproven found out that my slave cylinder crapped out, its ... Feb 14, 2012 - 11:47 PM trdproven i guess 1sttoyotaparts only has 1 kind, that shoul... Feb 14, 2012 - 11:59 PM BonzaiCelica why don't you just buy the rebuild kit for the... Feb 15, 2012 - 2:02 AM Smaay ^^^ dont need a master, its the salve that crapped... Feb 15, 2012 - 10:04 AM bigb1970 I have seen these leaking before.. Feb 15, 2012 - 11:38 AM BonzaiCelica there's a write up on how to rebuild your slav... Feb 15, 2012 - 12:30 PM azian_advanced the master is mounted on the firewall behind the s... Feb 15, 2012 - 3:04 PM BonzaiCelica no azain of course I know that ^^^^^
functi... Feb 16, 2012 - 12:41 PM BonzaiCelica alright so I'm looking for a clutch master cyl... Mar 22, 2012 - 4:49 PM trdproven I already replaced it a while ago, its all good no... Mar 22, 2012 - 6:17 PM BonzaiCelica so I'm having issues right now. about 7,000 mi... Apr 9, 2012 - 5:52 PM trdproven First make sure no air is in the system (as any hy... Apr 9, 2012 - 5:57 PM rave2n Definately make sure that fork on the trannie atta... Apr 10, 2012 - 8:12 AM trdproven theres only a few things to check of course leaks ... Apr 10, 2012 - 8:20 PM BonzaiCelica thanks for the info guys!!! this shoul... Apr 11, 2012 - 12:00 PM trdproven yea bleed until the slave stops like hes spitting ... Apr 11, 2012 - 5:30 PM
BonzaiCelica QUOTE (trdproven @ Apr 11, 2012 - 6... Apr 11, 2012 - 6:01 PM trdproven naw hydraulics is a closed system, you only need t... Apr 12, 2012 - 6:21 AM BonzaiCelica QUOTE (trdproven @ Apr 12, 2012 - 6... Apr 17, 2012 - 2:27 AM trdproven for example if you pump, does that slave rod move?... Apr 18, 2012 - 2:33 AM BonzaiCelica wow awesome. thanks much for the help. Luckily I s... Apr 18, 2012 - 1:33 PM rave2n QUOTE (BonzaiCelica @ Apr 18, 2012 - 1... Apr 18, 2012 - 1:59 PM Special_Edy QUOTE (BonzaiCelica @ Apr 18, 2012 - 2... Apr 18, 2012 - 2:02 PM trdproven the boot is just like any other rubber cover on yo... Apr 18, 2012 - 7:01 PM BonzaiCelica This slave cylinder came with original tranny that... Apr 22, 2012 - 3:49 AM trdproven there would be a lot of brake fluid and create a m... Apr 22, 2012 - 6:28 AM BonzaiCelica This was the condition from the first slave cylind... Apr 23, 2012 - 2:22 AM trdproven you need to close the bleeder, pump 3 times, hold ... Apr 23, 2012 - 3:12 AM BonzaiCelica http://www.wikihow.com/Bleed-a-Slave-Cylinder
^^^... Apr 23, 2012 - 2:49 PM trdproven i usually go for 1 and 3, for the vacuum pump kit ... Apr 23, 2012 - 5:18 PM Special_Edy Attach a clear hose to the bleeder nipple, and imm... Apr 23, 2012 - 6:49 PM BonzaiCelica QUOTE (Special_Edy @ Apr 23, 2012 - 6... Apr 25, 2012 - 3:47 AM BonzaiCelica QUOTE (trdproven @ Apr 23, 2012 - 5... Apr 23, 2012 - 11:21 PM Special_Edy You dont need it on or off, but from presonal expe... Apr 23, 2012 - 11:53 PM trdproven that looks like the right hose, i also use like a ... Apr 25, 2012 - 5:53 PM BonzaiCelica QUOTE (trdproven @ Apr 25, 2012 - 6... Apr 25, 2012 - 6:08 PM BonzaiCelica bump can anyone answer my question ^^^ Apr 26, 2012 - 2:30 PM mkernz22 What the heck? Why is the pin not in there already... Apr 26, 2012 - 2:36 PM BonzaiCelica what the helk is gravity bleed??
So I can still ... Apr 26, 2012 - 7:59 PM azian_advanced ... to bleed without pumping the pedal and letting... Apr 26, 2012 - 9:55 PM trdproven ^ gravity bleeding just takes eons. but yea its n... Apr 27, 2012 - 5:12 AM BonzaiCelica Pepboys (LuK brand) Apr 27, 2012 - 9:46 PM trdproven that looks more like it. try it out. Apr 28, 2012 - 4:36 AM BonzaiCelica First I just installed the new slave cylinder and ... Apr 30, 2012 - 2:44 PM BonzaiCelica which way is better to bleed the slave cylinder. I... Sep 1, 2012 - 1:08 AM trdproven QUOTE (BonzaiCelica @ Sep 1, 2012 - 4... Sep 1, 2012 - 8:05 AM BonzaiCelica i swapped out the master cylinder for a new one fr... Sep 1, 2012 - 11:54 PM trdproven QUOTE (BonzaiCelica @ Sep 2, 2012 - 2... Sep 2, 2012 - 2:00 AM BonzaiCelica HEY READ from the bottom of page 1 to the end of p... Sep 2, 2012 - 1:45 PM trdproven yea you dont want the clutch pedal taller than the... Sep 4, 2012 - 5:00 AM BonzaiCelica yea it is above the brake pedal and this is wha... Sep 4, 2012 - 2:12 PM trdproven QUOTE (BonzaiCelica @ Sep 5, 2012 - 5... Sep 4, 2012 - 6:05 PM BonzaiCelica Well I finally figured out how to adjust the lengt... Sep 5, 2012 - 1:26 PM trdproven QUOTE (BonzaiCelica @ Sep 6, 2012 - 4... Sep 5, 2012 - 10:10 PM BonzaiCelica I bought a 32 ounce bottle of o'reilly brand b... Sep 5, 2012 - 10:46 PM BonzaiCelica is this heat shield stock or only on beams/jdm mot... Oct 25, 2012 - 3:07 PM richee3 BEAMS slave cylinders, possibly GT4 as well but de... Oct 25, 2012 - 3:18 PM BonzaiCelica want! that is so oem. did you get one on your ... Oct 25, 2012 - 9:59 PM richee3 I have one but I haven't gotten around to putt... Oct 26, 2012 - 5:58 AM |
9 User(s) are reading this topic (9 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: December 4th, 2024 - 10:05 AM |