 how to make turbo spool sooner |
 Jun 6, 2012 - 12:41 PM
|
 
|
|
Enthusiast  Joined Sep 22, '10 From pomona, ca Currently Offline Reputation: 1 (100%)  |
im been wondering how to make my turbo spool faster, so i been searching a lot and all i find is junk. some say to port my exhaust inlet some say not to do it. other say so upgrade to bigger exhaust piping....... its confusing..
has anyone here actually tried doing something like that and notice any good results? i ask this because my turbo starts spooling at 3000RPM and i reach full boost (11psi) at around 3,800 rpm. i would like to reach full boost way before that.... i got a generic t3t4 .57 trim and i believe the exhaust side is .63 on my 94 gt, internal waste-gate w/ manual boost controller, 2 1/2" exhaust piping all help is appreciated |
 |
Replies
|
Jun 6, 2012 - 1:40 PM
|
|
|
Enthusiast Joined Jun 25, '06 From Box Elder, South Dakota Currently Offline Reputation: 2 (100%) |
There are quite a few ways to allow your turbo to spool "faster". Could be as simple as getting larger exhaust piping from the down pipe on back (upgrading to 3in or larger exhaust). Could also be a more efficient inter-cooler. Better flow within the cylinder head etc. etc...Hate to say this but it depends alot on how much money you have and really what you plan on doing with your car or engine.
All in all there are alot of things that can be done, that in general, will improve the efficiency of your engine altogether (or car). As far as advice goes i cant offer any specifics towards your setup other than a larger diameter exhaust (such as a 3in down-pipe, catback, mid-pipe etc.). Maybe some of the More experienced will give much more helpful ideas ^_^ This post has been edited by 3WayStunna: Jun 6, 2012 - 1:41 PM -------------------- (\__/)
(='.'=) This is bunny. Copy and paste bunny into your (")_(") signature to help him gain world domination. |
Posts in this topic
batcavee00 how to make turbo spool sooner Jun 6, 2012 - 12:41 PM
PhoenixTech Quicker spool time? put a smaller turbo on. you... Jun 7, 2012 - 9:47 AM lagos Remove fuel + add ignition timing = quicker spool. Jun 7, 2012 - 9:59 AM
Smaay QUOTE (lagos @ Jun 7, 2012 - 7:59 AM... Jun 7, 2012 - 10:42 AM Syaoran QUOTE (Smaay @ Jun 7, 2012 - 11:42 A... Jun 7, 2012 - 2:05 PM delusionz Disco potato. Jun 7, 2012 - 7:47 PM batcavee00 thanks guys for all the info. i guess ill just sti... Jun 8, 2012 - 11:32 AM Syaoran Boost leaks will make you not only "spool slo... Jun 8, 2012 - 6:02 PM Sunny Hi,
to name a few methods except of fluid dynamic... Jun 10, 2012 - 7:43 AM batcavee00 PROBLEM SOLVED!
2 things were wrong with my ... Jun 19, 2012 - 10:58 AM Smaay having a good wastegate make a world of difference... Jun 19, 2012 - 11:04 AM delusionz I have the new tial mvr 44mm unit too, using the 3... Jun 19, 2012 - 10:37 PM l0ch0w Unless you are running antilag, the only real way ... Jun 24, 2012 - 12:50 PM Smaay although it did fix your problem the BOV probably ... Jun 25, 2012 - 9:39 AM vplukas101 Go catless, bigger exhaust smaller turbo you will ... Jun 25, 2012 - 10:32 AM batcavee00 when i did the leak test the engine was off, but i... Jun 25, 2012 - 12:03 PM match220 my older mexican friend used to drag race a lot in... Jun 28, 2012 - 5:27 PM 3WayStunna QUOTE (match220 @ Jun 28, 2012 - 5:2... Jun 28, 2012 - 8:42 PM match220 QUOTE (3WayStunna @ Jun 28, 2012 - 3... Jun 28, 2012 - 9:01 PM Bitter You'd need the air nozzle IN the housing thoug... Jun 28, 2012 - 9:39 PM batcavee00 lmao that crazy, blowing compressed air on the exh... Jul 5, 2012 - 1:11 PM azian_advanced i'd be concerned about the sudden burst of com... Jul 5, 2012 - 5:44 PM match220 QUOTE (azian_advanced @ Jul 5, 2012 - 12... Jul 5, 2012 - 5:56 PM Rusty not very cost effective, but CO2 injection
http:/... Jul 5, 2012 - 8:59 PM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: November 27th, 2024 - 8:27 AM |