 snapped intake cam on a gen III |
 Aug 16, 2012 - 10:56 PM
|
 
|
 Enthusiast  Joined May 13, '06 From Kaimuki, HI Currently Offline Reputation: 10 (100%)  |
Is it common for the 3rd gen to snap a camshaft? I don't think it matters, but I'm running 3sgte cams in a 3sge head (head has turbo springs). As far as I know the 3sgte and 3sge heads are the same with the exception of the valve covers.
-------------------- -Jay
95 GT conv. project car: Manual, Gen III 3sgte, JN pisons, Eagle rods, overbore, crank knife-edged, crank scraper, ARP head/main/flywheel, Autronic EMS, Haltech Dual Wideband O2 controller, Audi 1.8T individual coils, FMIC and SSQV BOV, 3" downpipe, 3" ultra-high-flow cat, 2.5" Borla muffler, +other 01 S2000: FMIC, Haltech EMS, Haltech wideband, 570cc inj, forged pistons/rods, sleeved block, 5 angle valve job, ported and polished 02 R6, all stock, except for braided stainless brake lines, frame sliders, and adjustable brake/clutch leve |
 |
Replies
|
Aug 17, 2012 - 12:27 PM
|
|
 Enthusiast Joined Oct 29, '11 From Haltom City, Texas Currently Offline Reputation: 1 (100%) |
QUOTE (match220 @ Aug 16, 2012 - 11:56 PM)  Is it common for the 3rd gen to snap a camshaft? I don't think it matters, but I'm running 3sgte cams in a 3sge head (head has turbo springs). As far as I know the 3sgte and 3sge heads are the same with the exception of the valve covers. It would take a catastrophic event to snap a camshaft. Im fairly certain that the valves or timing compenents would break first and save the camshaft. Pull off the upper timing belt cover, the piece that says "3sgte Yamaha", and verify that the timing belt and cam sprockets are intact. Now, with the upper timing belt cover removed, you can turn the engine over and verify the camshafts are turning by watching the sprockets or noting their position before and after you turn the engine over. This post has been edited by Special_Edy: Aug 17, 2012 - 12:27 PM |
Posts in this topic
match220 snapped intake cam on a gen III Aug 16, 2012 - 10:56 PM
match220 QUOTE (Special_Edy @ Aug 17, 2012 - 7... Aug 17, 2012 - 5:34 PM
Special_Edy Is it in 2 pieces? That sounds pretty gnarly if it... Aug 17, 2012 - 5:51 PM match220 QUOTE (Special_Edy @ Aug 17, 2012 - 12... Aug 17, 2012 - 6:23 PM lagos Where your valve clearences all in spec when you i... Aug 17, 2012 - 9:44 PM match220 QUOTE (lagos @ Aug 17, 2012 - 4:44 P... Aug 18, 2012 - 1:11 AM Bitter A warped head will snap cams like that, have them ... Aug 17, 2012 - 10:29 PM match220 QUOTE (Bitter @ Aug 17, 2012 - 5:29 ... Aug 24, 2012 - 7:38 PM Bitter Also, sometimes you just get a defective part. Aug 18, 2012 - 9:58 AM Bitter Damn, I hate it when I'm right! Aug 27, 2012 - 12:33 AM |
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: February 20th, 2025 - 9:24 PM |