Press brake piston into caliper bore?, how to do that? Options

[dangqiwu]

Can't press piston into caliper bore. Any advice?


This post has been edited by dangqiwu: Jan 2, 2013 - 11:35 PM

[Nial]

I dont think you will need any tools, remove the brake pads, press the brake pedal once or twice, enough to push the piston out by a half inch or so, remove the rubber boot, you might need a small flat blade screw driver to wangle the metal spring clip off the outside of the boot. once the boot is removed look at the brake piston, if its nice and clean then you should be able to push it back in, However, corrosion will cause the piston to jam against the seal which is perhaps why it wont go back in. You will need to replace the piston with a new or rust free second hand one, in an ideal world you should change the seal too, but you can sometimes get away with reusing the old one if it has not suffered any damage.

[dangqiwu]

I dont think you will need any tools, remove the brake pads, press the brake pedal once or twice, enough to push the piston out by a half inch or so, remove the rubber boot, you might need a small flat blade screw driver to wangle the metal spring clip off the outside of the boot. once the boot is removed look at the brake piston, if its nice and clean then you should be able to push it back in, However, corrosion will cause the piston to jam against the seal which is perhaps why it wont go back in. You will need to replace the piston with a new or rust free second hand one, in an ideal world you should change the seal too, but you can sometimes get away with reusing the old one if it has not suffered any damage.

The piston looks OK, just several point of rust.

Would it help if I loose the bleeder screw?

Oh I would not do all that. Take out the brake pads(remembering how they go) and just get a c clamp and press the caliper back slowly moving side to side.
Make sure to remove brake resiviour cap because your fluid will rise back up, and put the cap BACK on before pressing the brakes after you are done. Or you will have to bleed brakes.

I tried with a C-Clamp but it's not working...

[Nial]

I dont think you will need any tools, remove the brake pads, press the brake pedal once or twice, enough to push the piston out by a half inch or so, remove the rubber boot, you might need a small flat blade screw driver to wangle the metal spring clip off the outside of the boot. once the boot is removed look at the brake piston, if its nice and clean then you should be able to push it back in, However, corrosion will cause the piston to jam against the seal which is perhaps why it wont go back in. You will need to replace the piston with a new or rust free second hand one, in an ideal world you should change the seal too, but you can sometimes get away with reusing the old one if it has not suffered any damage.

The piston looks OK, just several point of rust.

I dont know if you have succeeded yet?

When you say "several point of rust"...where abouts? it wont take much rust/corrosion to jam up a piston enough to stop it from fully returning. if that rust happens to be making contact with the seal, simply forcing it back in will not do you any favours at all. It can lead to damage to the seal which at best will leave you with leaking brakes, at worst brake failure (a little over dramatic but it can easily happen).

Using a C-Clamp to push the piston back in will easily give you enough force to return the piston home (normally you should be able to do it by hand) if that is not working then there is perhaps another issue going on that needs investigating before any permanent damage is done.

The two most common reasons for the piston not being able to be pushed in....as mentioned corrosion on the piston making contact with the seal, or the piston being forced in such a way that it is now at a slight angle to the calliper, using a c-clamp usually pushes the piston straight! unless you have tried before to lever it in using a screw driver or something?

Maybe another photo or the corrosion might help.


or am I too late and you now have it all sorted?

This post has been edited by Nial: Dec 23, 2012 - 12:23 AM