the birth, death and re-birth of a Skyline Options

[mrgt4]

just a post of the car and its history really, might be of interest in progression.

The car is a R32, was bought and we presumed an RB20 block... missfired and engine didnt run right to start so we did the usuals and changed the fuel filter, plugs and put a wasted spark kit on it to rid of the coil packs.

this sorted the running problems and then we went to the nurburgring, this however blew the headgasket... we didnt know this till home though as other than over heating no hg symptoms showed, we tried running with no thermostat to keep water pemanantly open, over heating still happend, just took longer.

we limped it home 500miles and took the head off to find the hg mullered and the number 1 cylinder full of water how the hell it made it home under own steam il never know.

so then we found the engine had forged interals and was a bored out RB25 block.. bonus!.

so i set to changing the rb20 turbo for an rb25turbo that we had, walbro fuel pump, tein superstreet coilovers, a blitz induction, and our FMIC conversion.
The subframe was dropped, suspension bushes changed etc.

well here more detailed, we got the car back from germany and whipped the head off, cylinder 1 full of water... not good, turned out to be head gasket failure so we sent the head off for skimming.

dead car..



Under the head was when we realised the car wasnt what we first thought it was... forged pistons, conrods and and bored out rb25 block!


once the head came back we had done some alterations:

FMIC conversion
a new downpipe
fixed the broken hanger on the rear silencer
gutted the cat
fitted a new walbro pump
a new fuel tank
new EBC discs and yellow stuff pads
an RB25 turbo
Full set of DEFI gauges, Oil temp, Oil pressure , Water temp and Boost pressure, all recordable so we knew what the engine was doing.
Removed all the hicas rear steering pipes and weilded up the pump so no leaks and locked out the bar.

the head came back and we put it all back together, ran it slow for a while as we had boost spike issues, this turned out to be that the wastegate path was too narrow and was causing massive boost spikes to 1.8bar!
back to the standard turbo elbow and this solved the problems.


The changes ended for the time being as work for me became too busy.

a drift /sprint day we organised then ensued and the car had its first real outing, and it ran a dream in which it went all day without missing a beat, same said for my gt4 bar me oversteering into a near by field. haha

THis brought about the start of the bodywork.

So i set to sanding back the old paintwork as i wanted to re-spray the car from a blank canvas so to speak.

To start we needed to rid the car of the rust over the rear wheel arches, there was a massive amount!
As we are putting wide arches on the the rear we cut the arches very high to make sure all rust was gone in preparation for priming and painting.

i let Jo loose with the grinder to his car!











front and rear




awaiting parts for my da sander i made best with what i had So we set with the sander and off i went..








removing the bumper



im sanding.... and jo.. well, sitting in a chair! :lol considering its his car... lazy bugger


remember... no drinking at work... unless its on a friends car or your own.. then its ok. :lol



a few hours at work.. but we are getting there



after sorting out the big triple sized garage for my spray booth the work again has started on the skyline, so this weekend i spent the time spraying some parts on the evo and the liner together, just primering stage at the moment but its all coming together well, heres the pictures.

the liner with new wide arches blended and filler primered, also starting to primer with the real proper primer prepped for painting so on she goes..



rear quarter nicely primered up and smooth as anything




passenger side..




the bottom of the door isnt primered yet as i have to do some work on it yet and shall be removing the wing mirror next week too..


alot of work left on the drivers side to do...


new wings need blending in as you can see, i need to make up a new bracket for the fuel cap or make a new fuel cap totally as the new arches litterally are 3 inches to 4 inches wider than standard!





so next weeks jobs on the liner are as follows, finish the whole car in primer and get the rear quarted smoothed and blended in to the car ready for primer.

also cracked on with the evo gsr spoiler while doing the liner as i have got a fair bit of work to do on an evo too.. sprayed spoler in parts but just to show the primered look i put it back in situe unbolted..









but the liner is FINALLY getting to make shape, i shall post more pics up this weekend when i set back to work on it!

when finished it shall be a "blurple" colour as my friend calls it, or thats the colour he wants me to re-spray it anyway, so i will just do as he wants but so far, the progress is as above, more this weekend!

from a bag of nails to a lovely car we are hoping, well i know it will look nice but being a datsun, who knows how long it will last. :lol:

anyhow, cheers

dale