 Exhaust Fitment Issues, Coupe/Convertible exhaust on Liftback chassis |
  |
 Dec 24, 2015 - 1:27 PM
|
 
|
 Enthusiast  Joined Apr 24, '08 From Orange County, CA Currently Offline Reputation: 33 (100%)  |
Well no one's bitten at my fujitsubo exhaust(10days now) so I might consider keeping it if I don't sell by end of January. I actually like the sound it produces as I had a friend drive it while I was outside
But how do I prevent the muffler from banging on the crash bar? I can bairly just fit my pinky finger between muffler and crash bar.  Sure I can put some sort of padding, but that will eventually wear down. And removing crash bar will make it unsafe if someone hits me. Should I just chop away at crash bar and then spray primer to prevent rust? This post has been edited by BonzaiCelica: Dec 24, 2015 - 8:43 PM -------------------- Group buy to replicate Narrow E series transaxle parts
http://www.6gc.net/forums/index.php?showto...p;#entry1107514 |
|
Dec 24, 2015 - 2:45 PM
|
|
 Enthusiast Joined Mar 8, '04 From Newport, RI Currently Offline Reputation: 63 (99%) |
Try...
Trim the bar a bit with a cut off wheel on a grinder or Adjust the hangers or Bigger (longer) rubber hangers. I would trim the bar a bit. -------------------- |
|
Dec 24, 2015 - 5:12 PM
|
|
|
Enthusiast Joined Apr 24, '08 From Orange County, CA Currently Offline Reputation: 33 (100%) |
Would some polyurethane hangers work?
-------------------- Group buy to replicate Narrow E series transaxle parts
http://www.6gc.net/forums/index.php?showto...p;#entry1107514 |
|
Dec 24, 2015 - 5:15 PM
|
|
 Enthusiast Joined Apr 17, '10 From U.P. michigan GO STATE Currently Offline Reputation: 3 (100%) |
I have very close clearances with the over axle 3in, only solution that helped was poly hangers.
-------------------- It takes 8,460 bolts to assemble an automobile, and one nut to scatter it all over the road.
 Celica: The name is derived from the Spanish word for "heavenly" or "celestial". Back-2-Back July COTM 15&16 |
|
Dec 24, 2015 - 8:43 PM
|
|
|
Enthusiast Joined Apr 24, '08 From Orange County, CA Currently Offline Reputation: 33 (100%) |
Their we go that's a much better picture
-------------------- Group buy to replicate Narrow E series transaxle parts
http://www.6gc.net/forums/index.php?showto...p;#entry1107514 |
|
Dec 25, 2015 - 9:04 AM
|
|
|
Enthusiast Joined Apr 17, '10 From U.P. michigan GO STATE Currently Offline Reputation: 3 (100%) |
I would cut the bar a bit, and use poly hangers for the rear muffler section. My clearance over the sub frame was very similar to that and poly hangers took care of the issue.
-------------------- It takes 8,460 bolts to assemble an automobile, and one nut to scatter it all over the road.
Celica: The name is derived from the Spanish word for "heavenly" or "celestial". Back-2-Back July COTM 15&16 |
|
Dec 25, 2015 - 9:09 AM
|
|
|
Enthusiast Joined Mar 8, '04 From Newport, RI Currently Offline Reputation: 63 (99%) |
Sledgehammer.
-------------------- |
|
Dec 25, 2015 - 1:51 PM
|
|
 Enthusiast Joined Mar 15, '07 From Tennessee Currently Offline Reputation: 52 (100%) |
get a coupe. Problem solved
-------------------- Learned a lot in 10 years... I hardly log in anymore, last login Today Sept 6 2019, and I was forced just to clarify a post. LOL
If you PM me and I dont respond, dont fret or cry. Im alive, better post your questions in the thread below, maybe I log back in 2grfe Swapped... Why I chose the 2GR, before you ask read here... A great civilization is not conquered from without until it has destroyed itself from within. @llamaraxing in Instagram is the best way to find me. I hardly log here anymore. |
|
Dec 25, 2015 - 5:04 PM
|
|
|
Enthusiast Joined Apr 24, '08 From Orange County, CA Currently Offline Reputation: 33 (100%) |
Oh yea well like your exhaust is to restrictive for your V6. I mean like geez have some respect for that engine, upgrade to 70mm piping and sell me your exhaust.
You know so you can get ready for your supercharger ahead of time n stuff 
-------------------- Group buy to replicate Narrow E series transaxle parts
http://www.6gc.net/forums/index.php?showto...p;#entry1107514 |
|
Dec 25, 2015 - 7:27 PM
|
|
|
Enthusiast Joined Mar 11, '06 From Way South Chicago Currently Offline Reputation: 0 (0%) |
QUOTE (Batman722 @ Dec 25, 2015 - 8:09 AM)  Sledgehammer. This is the solution. -------------------- |
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: November 27th, 2024 - 2:06 PM |