My 3rd Gen 3SGTE Swap Thread, It lives!!! Pg8 Options

[bccentaur3]

I know that the s54 is strong. Mine has proven itself up until the input shaft of the cv shaft snapped inside the diff, causing me to lose reverse. When that happened I struck a deal on an e153 lsd trans.

[presure2]

Lucky, the power steering pump on the 3rd gen is easy to work with.

So are you going to be using an e153 transmission or stick with the tired s54? I'm surprised that transmission has held up through all those years of your beating lol!!

I'll be using the same s54. I can't afford to do the e153 swap right now.

No big plans for the motor, I'm just gonna add a helper spring for the wastegate, make a nice 3" intake, use the water injection off the 5sfte setup, the same MBC and exhaust with a new front peice, although I may add a resonator to quiet it down a little around town.
I'd like to install cam gears... I'm trying to trade some bodywork labor for them with a fellow member... (we love u Steff!!)
that's about it other than cleaning things up and tidying up the engine bay.

This weekend we are working on dissasembling the clip, I cut the spot welds and removed the radiator support Thursday, today I'm gonna take the dash, ect off and start cutting the clip up down to the firewall.
Pics tonight!

[samir0189]

looking forward to those pics. Hope everything goes well.

[SlvrCelica09]

I know that the s54 is strong. Mine has proven itself up until the input shaft of the cv shaft snapped inside the diff, causing me to lose reverse. When that happened I struck a deal on an e153 lsd trans.

oh true.. the e153 is probably the best bet in the long run.

[bccentaur3]

Soooo RHD conversion??

[Ted95]

I know that the s54 is strong. Mine has proven itself up until the input shaft of the cv shaft snapped inside the diff, causing me to lose reverse. When that happened I struck a deal on an e153 lsd trans.

oh true.. the e153 is probably the best bet in the long run.

im doing basically the same swap as manny (only with a FMIC) and im reusing my stock s54 tranny withhhhh 205k on it .. it drives and shifts pretty clean, u think it will hold with the mileage?

[6G96GT]

This is just the thread I need to read up on! Looking forward to that turbo swap man! Looks good so far!

This post has been edited by 6G96GT: Apr 10, 2010 - 8:18 PM

[bccentaur3]

I know that the s54 is strong. Mine has proven itself up until the input shaft of the cv shaft snapped inside the diff, causing me to lose reverse. When that happened I struck a deal on an e153 lsd trans.

oh true.. the e153 is probably the best bet in the long run.

im doing basically the same swap as manny (only with a FMIC) and im reusing my stock s54 tranny withhhhh 205k on it .. it drives and shifts pretty clean, u think it will hold with the mileage?

It'll hold mine, had 215,000 until it went due to the broken axle.

[presure2]

Soooo RHD conversion??

DEFINETLY NOT.
all those parts are for sale, like SUPER cheap.
i just want someone to come get them out of my garage. lol
got most of the frame rails cut off last night, and all the dash parts off and basicly got it down to the bare firewall.
didnt take pics while we were doing it, ill go out in a bit and get some pics of the carnage. lol

when we got the clip, the intercooler and stuff on top of the motor seemed to have this weird "film" on it, almost textured, that seemed to trap most of the dust and dirt that is visable on the motor.
i took a little lacquer thinner to a corner of the IC, and it started comming off, it almost seems like the previous owner may have attempted to spray some kind of clear coat over things, but very poorly.
once i started wiping it off, the intercooler REALLY started to come back to life.
a quick pic i snapped last night of the results ( you can see the film on the entry neck of the IC still):



yummy!

for you guys that may see this, and are looking for RHD parts, be on the lookout for a for sale thread soon, i have the FULL dash minus the CC unit, and full front SS suspension and steering rack, excluding brakes and of course all the RHD firewall stuff.

cameron, start your own thread for your questions about your swap. but since the thread jack is already on:
the S54 will be just fine, provided its in good shape when you start, and your not bangin gears like your a race car driver, and launching it at every stop light like your racing NHRA.
my tranny has been taking a beating at close to and over 300hp for just about 5 years now, and art (lagos) has been on his stock tranny for longer than that.

[pipes]

do u have the dash harness?

[block]

im hoping to get something like this done but it's harder and harder to find a clean celica how hard is this going to be? 2nd and 3rd gen basically the same, installation-wise?

[presure2]

im hoping to get something like this done but it's harder and harder to find a clean celica how hard is this going to be? 2nd and 3rd gen basically the same, installation-wise?

IMO a 3rd gen is an easier swap, cause there is less wiring.
the basic mechanical parts of the swap are the same as any other swap.

[Ted95]

Soooo RHD conversion??

DEFINETLY NOT.
all those parts are for sale, like SUPER cheap.
i just want someone to come get them out of my garage. lol
got most of the frame rails cut off last night, and all the dash parts off and basicly got it down to the bare firewall.
didnt take pics while we were doing it, ill go out in a bit and get some pics of the carnage. lol

when we got the clip, the intercooler and stuff on top of the motor seemed to have this weird "film" on it, almost textured, that seemed to trap most of the dust and dirt that is visable on the motor.
i took a little lacquer thinner to a corner of the IC, and it started comming off, it almost seems like the previous owner may have attempted to spray some kind of clear coat over things, but very poorly.
once i started wiping it off, the intercooler REALLY started to come back to life.
a quick pic i snapped last night of the results ( you can see the film on the entry neck of the IC still):



yummy!

for you guys that may see this, and are looking for RHD parts, be on the lookout for a for sale thread soon, i have the FULL dash minus the CC unit, and full front SS suspension and steering rack, excluding brakes and of course all the RHD firewall stuff.

cameron, start your own thread for your questions about your swap. but since the thread jack is already on:
the S54 will be just fine, provided its in good shape when you start, and your not bangin gears like your a race car driver, and launching it at every stop light like your racing NHRA.
my tranny has been taking a beating at close to and over 300hp for just about 5 years now, and art (lagos) has been on his stock tranny for longer than that.

wasnt trying to start a thread jack big guy but thanks for the tranny info. ill be starting my own thread soon, jus gotta get a few more things b4 i start strippin a few things down.
IC looks goood man! keep it up bro!

[RUNNIN-LOW]

OMFG!!!!!!!!!!!!!!!!!!!!!! wow!!! wow!!! im glad to see what you are doing P! welcome to the gen3 family! sorry been missing for so long..as for the s54 tranny it will hold up to the stock power..i think i even liked it more, it feels so much lighter and you can feel the power to the ground when you push it..the e153 is just too heavy but thats just me...

keep us updated P! Yahs! just blowing people away!

[presure2]

so heres some pics of the progress since the last post.

after removing the dash and whatnot:



after cutting back the frame rails:



after cutting out the firewall (no, i didnt drill out the welds, leave that for the guy who buys it! lol)



floor and door pillars:



cut in half for easy transportation:



now i gotta get rid of all the scrap, clean up the garage, and start prepping the motor! WOOT

[SwissFerdi]

That is one massacred ex-GT-4. At least its heart is going to the right place.

[presure2]

last night i spent ~1hr in the garage, things are still a mess, but we should be taking all the junk metal over to the scrappers today, so that will free up some space and allow me to actually start working on the motor.
i spent a little time cleaning up the blitz BOV that came on the clip, its not 100% done, and i am not planning on using it on this swap, but i wanted to see if it would shine back up, so that if i end up selling it, it looks good for the next guy who owns it.
its the blitz super sound, after googling for some vids of it, i actually like how it sounds.

before:



after:





also, steff ordered the cam gears for me, ((WOOOT thank you steff, i appreciate your help!!)) so they should arrive soon, and she also got the t-belt for me, so once the gears arrive, ill have some good pics ect of the timing belt side of the motor while i am doing my thing.

[6gtfour]

If the right side ac vent and the radio bezel are in good condition pm me a price for those I don't know if you have the shifter bezel if you do pm me a price for all 3 parts. been trying to get these in Right hand drive config for a while now

[Ted95]

wow that BOV cleaned up nice from what it was lol good work manny

[presure2]

this AM i wanna go out and start pulling some stuff off the motor, getting ready for the big push.
just a few more small things to order, and ill start getting it cleaned up and ready for the install in a few weeks.