 3s-gte rebuild |
  |
 Nov 15, 2011 - 9:36 AM
|
 
|
|
Enthusiast  Joined May 16, '10 From Raleigh Currently Offline Reputation: 12 (100%)  |
No, it needs to click in all the way. The transmission seal only works with axles that are pushed all the way in. Anything less, and your transmission will likely leak, and let in dirt.
--------------------  |
|
Nov 15, 2011 - 9:42 AM
|
|
|
Enthusiast Joined Nov 2, '06 From Finland Currently Offline Reputation: 0 (0%) |
So do i just need to hammer it on?
The other side clicked on very easy. This post has been edited by Gt4Driver: Nov 15, 2011 - 9:44 AM |
|
Nov 15, 2011 - 2:42 PM
|
|
|
Enthusiast Joined May 29, '09 From Gainesville, FL Currently Offline Reputation: 17 (100%) |
I had to tap mine in with a deadblow to an end of the CV joint. Don't want to damage the internals. Timing side is the long shaft right? if so that is the one I had to tap in, the other was easy.
Took a few good whacks, but once you hear the lock ring click, its in. Was on a ST trannie, but I assume same concept. |
|
Nov 15, 2011 - 3:51 PM
|
|
|
Enthusiast Joined Nov 2, '06 From Finland Currently Offline Reputation: 0 (0%) |
Oil sanwich plate install for oil pressure gauge and other.
   
|
|
Nov 15, 2011 - 4:21 PM
|
|
|
Enthusiast Joined Jan 19, '11 From Paraguay, Winchestertonfieldville Currently Offline Reputation: 1 (100%) |
my mechanic was preocupied by the oil press sensor when he put it in the sandwich plate...he said that when turning the wheel might hit it...just a heads up
-------------------- |
|
Nov 16, 2011 - 1:05 AM
|
|
|
Enthusiast Joined Nov 2, '06 From Finland Currently Offline Reputation: 0 (0%) |
Thanks for warning. i'll check that
|
|
Nov 16, 2011 - 3:41 PM
|
|
|
Enthusiast Joined Nov 2, '06 From Finland Currently Offline Reputation: 0 (0%) |
That fu***** driveshaft wont go in.
 Been hammering it all day. |
|
Nov 16, 2011 - 4:06 PM
|
|
|
Enthusiast Joined May 16, '10 From Raleigh Currently Offline Reputation: 12 (100%) |
Any way you could pull it out and take a pick of what the end looks like? May be damaged or something. Probably worth another opinion.
-------------------- |
|
Nov 16, 2011 - 4:14 PM
|
|
|
Enthusiast Joined Nov 2, '06 From Finland Currently Offline Reputation: 0 (0%) |
Ok. i'll take a pick tomorrow, now i need to go to sleep.
|
|
Nov 17, 2011 - 4:49 PM
|
|
|
Enthusiast Joined Nov 2, '06 From Finland Currently Offline Reputation: 0 (0%) |
it's in! just take it off and put it back. snap in pretty easy. Don't know what was wrong earlier.
 Maybe sunday i'll fire it up. |
|
Nov 20, 2011 - 4:19 AM
|
|
|
Enthusiast Joined Nov 2, '06 From Finland Currently Offline Reputation: 0 (0%) |
Ok. It's time to fire it up
 Hope everything is okay.
|
|
Nov 20, 2011 - 7:54 AM
|
|
|
Enthusiast Joined Nov 2, '06 From Finland Currently Offline Reputation: 0 (0%) |
No it wont start. starter just klicks.
|
|
Nov 20, 2011 - 9:33 AM
|
|
|
Enthusiast Joined Nov 2, '06 From Finland Currently Offline Reputation: 0 (0%) |
I hammered my starter and it starts to work
|
|
Nov 20, 2011 - 9:44 AM
|
|
|
Enthusiast Joined Jan 19, '11 From Paraguay, Winchestertonfieldville Currently Offline Reputation: 1 (100%) |
sounds like a new starter is in order...
-------------------- |
|
Nov 20, 2011 - 11:20 AM
|
|
|
Enthusiast Joined Nov 2, '06 From Finland Currently Offline Reputation: 0 (0%) |
Yes i think so. but it works now. Engine runs great!!!!!!
|
|
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: February 18th, 2025 - 3:04 PM |