 WTB: Some needed peices for my 3SGE Rebuild, ... anyone parting out a revIII 3S? |
  |
 Apr 25, 2012 - 10:07 AM
|
 
|
 Enthusiast  Joined Apr 18, '06 From Calgary, Canada Currently Offline Reputation: 37 (100%)  |
All parts need to be from a 3rd Gen 3SGE/3SGTE:
(1) Upper timing belt cover - FOUND (2) The alternator tensioner assembly seems to be missing from my engine - this is the 12mm bolt that will tighten the acc belt  (3) *stab in the dark here* - TRD Replica Wing (Hatchback) (4) Driverside Projector with NO broken tabs. (preferably just the housing, so if you have a wrecked one with tabs intact - I'll take it!!) I'm sure I will need more as the build progresses, so I will add to this list later, but these are the main ones for now. Thank you! Shipped to T4B 2V4 Alberta. This post has been edited by KAOS: Jun 5, 2012 - 12:33 PM -------------------- |
|
Apr 26, 2012 - 7:49 AM
|
|
|
Enthusiast Joined Apr 18, '06 From Calgary, Canada Currently Offline Reputation: 37 (100%) |
(2) Idle pulley assembly from a 3SGE - I think this might be different than on a 3SGTE... not sure however.
This post has been edited by KAOS: Apr 26, 2012 - 7:56 AM -------------------- |
|
Apr 26, 2012 - 7:56 AM
|
|
|
Enthusiast Joined Apr 18, '06 From Calgary, Canada Currently Offline Reputation: 37 (100%) |
(3) Ignition Coil Assembly Found! - THANKS HATCHY GT-S!!
This post has been edited by KAOS: Apr 26, 2012 - 11:13 AM -------------------- |
|
Apr 26, 2012 - 7:56 AM
|
|
 Enthusiast Joined Apr 17, '06 From New Jersey Currently Offline Reputation: 105 (100%) |
Part 88440-20120 (PULLEY ASSY, IDLE) was found on the following models: Date range Model Frames/Options Found in diagram 08/1985-07/1987 TOYOTA CELICA ST16* 87-19: HEATING & AIR CONDITIONING - COMPRESSOR 08/1987-07/1989 TOYOTA CELICA ST16* 87-19: HEATING & AIR CONDITIONING - COMPRESSOR 09/1989-08/1993 TOYOTA CELICA AT180,ST18* 87-19: HEATING & AIR CONDITIONING - COMPRESSOR is this the ingition coil assy part number ? 90919-02209 if so, Part 90919-02209 (COIL ASSY, IGNITION) was found on the following models: Date range Model Frames/Options Found in diagram 09/1993-07/1999 TOYOTA CELICA AT200,ST204 19-01: IGNITION COIL & SPARK PLUG 11/1995-07/2000 TOYOTA RAV4 SXA1* 19-01: IGNITION COIL & SPARK PLUG --------------------  |
|
Apr 26, 2012 - 11:10 AM
|
|
|
Enthusiast Joined Apr 18, '06 From Calgary, Canada Currently Offline Reputation: 37 (100%) |
QUOTE (Culpable04 @ Apr 26, 2012 - 6:56 AM)  Part 88440-20120 (PULLEY ASSY, IDLE) was found on the following models: Date range Model Frames/Options Found in diagram 08/1985-07/1987 TOYOTA CELICA ST16* 87-19: HEATING & AIR CONDITIONING - COMPRESSOR 08/1987-07/1989 TOYOTA CELICA ST16* 87-19: HEATING & AIR CONDITIONING - COMPRESSOR 09/1989-08/1993 TOYOTA CELICA AT180,ST18* 87-19: HEATING & AIR CONDITIONING - COMPRESSOR is this the ingition coil assy part number ? 90919-02209 if so, Part 90919-02209 (COIL ASSY, IGNITION) was found on the following models: Date range Model Frames/Options Found in diagram 09/1993-07/1999 TOYOTA CELICA AT200,ST204 19-01: IGNITION COIL & SPARK PLUG 11/1995-07/2000 TOYOTA RAV4 SXA1* 19-01: IGNITION COIL & SPARK PLUG Thanks Culp; I found the Ignition Assembly already. Just looking for this now: 
This post has been edited by KAOS: Apr 26, 2012 - 11:11 AM -------------------- |
|
May 1, 2012 - 11:39 AM
|
|
|
Enthusiast Joined May 17, '11 From Calgary Currently Offline Reputation: 1 (100%) |
QUOTE (KAOS @ Apr 26, 2012 - 11:10 AM) Just looking for this now: Ask Aaron at Lithia, maybe he can give you some direction QUOTE (sodap0pWRC @ May 1, 2012 - 11:37 AM) QUOTE (KAOS @ Apr 26, 2012 - 11:10 AM) Just looking for this now: Ask Aaron at Lithia, maybe he can give you some direction I might have a spare, but it would be in storage at my mom and dads. Want to take a drive to look? -------------------- 94 JDM ST205 WRC#2354 172,000 km (my baby)
94 JDM SW20 GT 151,500km (track car) 91 JDM ST185 RC 106600km (DD) 08 Sea Ray 185 Sport 220-hp MerCruiser® 4.3L MPI , BigAir tower, High5 SS prop. (38hours) |
|
May 4, 2012 - 2:34 AM
|
|
 Enthusiast Joined Mar 15, '07 From Tennessee Currently Offline Reputation: 52 (100%) |
-------------------- Learned a lot in 10 years... I hardly log in anymore, last login Today Sept 6 2019, and I was forced just to clarify a post. LOL
If you PM me and I dont respond, dont fret or cry. Im alive, better post your questions in the thread below, maybe I log back in 2grfe Swapped... Why I chose the 2GR, before you ask read here... A great civilization is not conquered from without until it has destroyed itself from within. @llamaraxing in Instagram is the best way to find me. I hardly log here anymore. |
|
May 7, 2012 - 10:37 PM
|
|
|
Enthusiast Joined Apr 18, '06 From Calgary, Canada Currently Offline Reputation: 37 (100%) |
QUOTE (njccmd2002 @ May 4, 2012 - 1:34 AM) Won't fit - doesn't line up properly, that one is probably a Gen 2. Bump. Anyone? -------------------- |
|
May 8, 2012 - 12:34 PM
|
|
|
Enthusiast Joined Apr 18, '06 From Calgary, Canada Currently Offline Reputation: 37 (100%) |
QUOTE (sodap0pWRC @ May 1, 2012 - 10:39 AM) I might have a spare, but it would be in storage at my mom and dads. Want to take a drive to look? Sure if you don't mind.  But I think I had a brain-fart here...  That bracket is only there if there's no A/C. And I haz A/C on my car - I just left the compressor attached to the lines in the engine bay...  
-------------------- |
|
May 18, 2012 - 1:29 AM
|
|
|
Enthusiast Joined Apr 18, '06 From Calgary, Canada Currently Offline Reputation: 37 (100%) |
Adding to the list:
(4) Driverside Projector with NO broken tabs. (preferably just the housing, so if you have a wrecked one with tabs intact - I'll take it!!) -------------------- |
|
May 19, 2012 - 7:15 PM
|
|
 Enthusiast Joined Jan 8, '09 From Netherlands Currently Offline Reputation: 54 (100%) |
You have PM
|
|
May 28, 2012 - 3:23 PM
|
|
 Moderator Joined Jun 29, '08 From Denver Currently Offline Reputation: 59 (100%) |
Do you need the whole belt tensioner assembly or just the bolt? Because I have both on my spare beam if the belt tensioner assembly will work for you.
-------------------- "Employ your time in improving yourself by other men's writings, so that you shall gain easily what others labored hard for." -Socrates. Even Socrates told us to use the search button!
 2006 Aston Martin V8 Vantage. 1998 Celica GT- BEAMS Swapped. 2022 4Runner TRD Off Road Prenium. 2021 GMC Sierra AT4. |
|
May 28, 2012 - 5:34 PM
|
|
|
Enthusiast Joined Apr 18, '06 From Calgary, Canada Currently Offline Reputation: 37 (100%) |
QUOTE (richee3 @ May 28, 2012 - 2:23 PM) Do you need the whole belt tensioner assembly or just the bolt? Because I have both on my spare beam if the belt tensioner assembly will work for you. I'd need the entire assembly. The arm that attaches to the block, the pulley, and the bolts, etc. (and the boldts that attach it to the block! ) Thanks! -------------------- |
|
May 28, 2012 - 7:20 PM
|
|
|
Moderator Joined Jun 29, '08 From Denver Currently Offline Reputation: 59 (100%) |
The one on my BEAMS looks very very similar. I'll get detailed pictures for you next time I head to my dad's house. Should be early next week if you haven't gotten one before then.
-------------------- "Employ your time in improving yourself by other men's writings, so that you shall gain easily what others labored hard for." -Socrates. Even Socrates told us to use the search button!
2006 Aston Martin V8 Vantage. 1998 Celica GT- BEAMS Swapped. 2022 4Runner TRD Off Road Prenium. 2021 GMC Sierra AT4. |
|
Jun 1, 2012 - 12:59 AM
|
|
|
Enthusiast Joined Jan 8, '09 From Netherlands Currently Offline Reputation: 54 (100%) |
QUOTE (KAOS @ May 8, 2012 - 5:37 AM) QUOTE (njccmd2002 @ May 4, 2012 - 1:34 AM) Won't fit - doesn't line up properly, that one is probably a Gen 2. Bump. Anyone? Yes I have it for sale, I did sent you some pictures
|
|
Jun 5, 2012 - 12:35 PM
|
|
|
Enthusiast Joined Apr 18, '06 From Calgary, Canada Currently Offline Reputation: 37 (100%) |
QUOTE (richee3 @ May 28, 2012 - 6:20 PM) The one on my BEAMS looks very very similar. I'll get detailed pictures for you next time I head to my dad's house. Should be early next week if you haven't gotten one before then. Any chance you made it out there yet?? QUOTE (RoyO @ May 31, 2012 - 11:59 PM) QUOTE (KAOS @ May 8, 2012 - 5:37 AM) QUOTE (njccmd2002 @ May 4, 2012 - 1:34 AM) Won't fit - doesn't line up properly, that one is probably a Gen 2. Bump. Anyone? Yes I have it for sale, I did sent you some pictures Thanks Roy! You rock! -------------------- |
|
Jun 5, 2012 - 2:03 PM
|
|
|
Enthusiast Joined Jan 8, '09 From Netherlands Currently Offline Reputation: 54 (100%) |
QUOTE (KAOS @ Jun 5, 2012 - 7:35 PM) QUOTE (RoyO @ May 31, 2012 - 11:59 PM) Yes I have it for sale, I did sent you some pictures Thanks Roy! You rock! No problem, money received, I'll ship it out tomorrow. I just left reputation feedback for you
|
|
May 21, 2014 - 4:05 PM
|
|
|
Enthusiast Joined Apr 18, '06 From Calgary, Canada Currently Offline Reputation: 37 (100%) |
 I need the following parts from the diagram: 87240 Heater Switch and all brackets/bolts etc 87246E & 87245A Heater Core Hoses Please please please please please please. Shipping to 77032. -------------------- |
|
May 21, 2014 - 4:11 PM
|
|
|
Enthusiast Joined Apr 18, '06 From Calgary, Canada Currently Offline Reputation: 37 (100%) |
 Part #: 33557-33010 This post has been edited by KAOS: May 21, 2014 - 4:12 PM -------------------- |
|
5 User(s) are reading this topic (5 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: November 29th, 2024 - 7:53 AM |