Importing Vehicles, If you ever considered a GT-Four Options

[darksecret]

This is about all the information from the DOT and NHTSA for importing a car, it's a lot of information but if you ever considered it then here is what you'll need.

1. Is there a need for DOT Approval?


DOT does not approve any motor vehicles or motor vehicle equipment items as complying with all applicable FMVSS. That is instead the responsibility of the vehicle or equipment item's original manufacturer. For motor vehicles, the certification is provided in the form of a label that is permanently affixed to the vehicle by its original manufacturer, stating that the vehicle complies with all applicable FMVSS in effect on its date of manufacture. For vehicles other than motorcycles or trailers, the label must be affixed to either the hinge pillar, the door latch post, or the door edge that meets the door-latch post, next to the driver's seating position. For motor cycles and motor driven cycles, the label must be affixed to a permanent member of the vehicle, as close as is practicable to the intersection of the steering post with the handlebars, so that it is easily readable without moving any part of the vehicle except for the steering system. For trailers, the label must be affixed to a location on the forward half of the left side of the vehicle, so that it can be easily read without moving any part of the vehicle.

2. Can NHTSA tell whether my vehicle is conforming?


Motor vehicle manufacturers are not required to submit to NHTSA, and do not submit to NHTSA, information on whether any particular vehicle they manufacture has been manufactured to comply with all applicable Federal motor vehicle safety (and, where applicable, bumper and theft prevention) standards. Moreover, there is no way for NHTSA to discern, from the VIN that has been assigned to a vehicle, or from any other identifying characteristic, whether the vehicle was originally manufactured to comply with all applicable standards. The only way that NHTSA could tell whether a given vehicle has been so manufactured is if the manufacturer has affixed a label to the vehicle certifying its compliance with all applicable standards. If you are unable to find a certification label on a particular vehicle, and are interested in learning whether the vehicle was originally manufactured to comply with all applicable standards, you should contact the vehicle's manufacturer. A list of manufacturer contacts can be found on NHTSA's website at http://www.nhtsa.dot.gov/cars/rules/import/.


3. Importing a conforming vs. a non-conforming vehicle.


If a motor vehicle was manufactured to comply with all applicable FMVSS, and bears a label certifying such compliance that was permanently affixed by its original manufacturer, there is no need for NHTSA approval before the vehicle is imported. However, the manufacturer would have to submit to the agency information identifying it and the products that it manufactures that are subject to our standards no later than 30 days after manufacturing begins. In addition, the manufacturer would have to submit to us information necessary to decipher the VIN that it must assign to each motor vehicle it manufactures for sale in the U.S. If the vehicle manufacturer is not located in the U.S. the manufacturer must also designate a U.S. resident as its agent for service of process.

If the vehicle is less than 25 years old and was not originally manufactured to comply with all applicable FMVSS, and/or was not so certified by its original manufacturer, it cannot be lawfully imported into the U.S. on a permanent basis unless NHTSA determines it eligible for importation. The agency makes those determinations on its own initiative or the basis of a petition from a registered importer. These are business entities that are specifically approved by NHTSA to import nonconforming vehicles and to perform the necessary modifications on those vehicles so that they conform to all applicable FMVSS. The petitions must specify that the vehicle is substantially similar to a vehicle that was certified by its original manufacturer as conforming to all applicable FMVSS and is capable of being readily altered to conform to those standards, or, if there is no substantially similar U.S.-certified vehicle, that the vehicle has safety features that comply with, or are capable of being altered to comply with, the FMVSS based on destructive test information or other evidence the agency deems adequate. Import eligibility decisions are made on a make, model, and model year basis.


An additional requirement for the lawful importation of a nonconforming vehicle is that it be imported by a registered importer (RI) or by an individual who has contracted with an RI to bring the vehicle into conformity with all applicable FMVSS. A bond in an amount equivalent to 150 percent of the declared value of the vehicle must be given at the time of importation to ensure that the necessary modifications are completed within 120 days of entry. A list of RI's can be found on our web site at http://www.nhtsa.dot.gov/cars/rules/import/. You might want to contact one or more of the listed RIs to obtain their opinion on the feasibility of conforming the vehicle that you seek to import to the FMVSS, and the costs involved in petitioning the agency to determine that vehicle to be eligible for importation, as well as the costs for conforming the vehicle to the FMVSS.


4. Importing a vehicle already determined eligible for importation.


NHTSA makes import eligibility decisions on a make, model, and model year basis. A list of vehicles that NHTSA has determined to be eligible for importation can be found on our web site at http://www.nhtsa.dot.gov/cars/rules/import/. If the vehicle you are seeking to import is of a make, model, and model year that is on that list, it can be imported by an RI, or by a person who has a contract with an RI to modify the vehicle so that it conforms to all applicable FMVSS and bumper standards after importation. At the time that NHTSA determines a vehicle of a particular make, model, and model year to be eligible for importation, the agency assigns the vehicle a unique vehicle eligibility number. That number is to be entered on the appropriate block of the HS-7 Declaration form that is to be given to Customs at the time of importation. The number alerts Customs to the fact that the vehicle can be lawfully imported (by an RI or by a person who has a contract with an RI to modify the vehicle), even though the vehicle was not originally manufactured to comply with all applicable FMVSS.


5. Importing a Canadian-certified vehicle; need for automatic restraints.


Before it can be lawfully imported into the U.S., a vehicle that was not originally manufactured to comply with all applicable FMVSS, and/or was not so certified by its original manufacturer, must first be determined eligible for importation by NHTSA. The agency has determined that Canadian-certified passenger cars manufactured on or after September 1, 1989, are eligible for importation, provided those vehicles are equipped with automatic restraints that meet the requirements of FMVSS No. 208, “Occupant Crash Protection.” If a vehicle manufactured on or after that date is not equipped with automatic restraints, it has not been determined eligible for importation. Without this determination, the vehicle cannot lawfully be imported into the U.S.


6. Re-importing a U.S.-certified vehicle.


If a vehicle now outside the U.S. bears a certification label affixed by its original manufacturer stating that the vehicle complies with all applicable FMVSS in effect on its date of manufacture, it can be imported as a conforming motor vehicle under Box 2A on the HS-7 Declaration form that must be given to Customs at the time of entry. You can download a copy of that form from our website at http://www.nhtsa.dot.gov/cars/rules/import.


7. Re-importing a U.S.-certified vehicle missing its certification label.


If your vehicle was originally manufactured to comply with all applicable FMVSS, and was so certified by its original manufacturer, it can be lawfully imported as a conforming motor vehicle under Box 2A on the HS-7 Declaration form to be given to Customs at the time of entry. If the vehicle is missing its certification label, it can still be imported as a conforming motor vehicle, provided you obtain a letter from the vehicle’s manufacturer stating that the vehicle was originally manufactured to comply with all applicable FMVSS. A list of manufacturer contacts is on our website at http://www.nhtsa.dot.gov/cars/rules/import/. If the manufacturer is unable or unwilling to supply you with a letter stating that your vehicle was originally manufactured to meet all applicable FMVSS, bumper, and theft prevention standards, we would be willing to issue you a letter stating that we recognize your vehicle as having been so manufactured, provided you can furnish us with evidence (preferably in the form of a State-issued registration document) showing that the vehicle was registered in the U.S. before it was shipped overseas. If you do not have the vehicle’s prior registration documents, you can furnish us a report from a commercial VIN checking service (such as Carfax) that identifies the vehicle’s prior registration history and shows that the vehicle was once registered in the U.S. If you have such evidence, you should fax it to the Imports and Certification Division at 202-366-1024.


8. Importing a vehicle that is at least 25 years old.


A motor vehicle that is at least 25 years old can be lawfully imported into the U.S. without regard to whether it complies with all applicable FMVSS. Such a vehicle would be entered under Box 1 on the HS-7 Declaration form to be given to Customs at the time of importation. If you wish to see that form, you may download a copy from our website at www.nhtsa.dot.gov/cars/rules/import. You should note that the 25 year period runs from the date of the vehicle's manufacture. If the date of manufacture is not identified on a label permanently affixed to the vehicle by its original manufacturer, to establish the age of the vehicle, you should have documentation available such as an invoice showing the date the vehicle was first sold or a registration document showing that the vehicle was registered at least 25 years ago. Absent such information, a statement from a recognized vehicle historical society identifying the age of the vehicle could be used.


9. Importing a vehicle for parts.


If a vehicle originally manufactured for on-road use is shipped with its engine and drive train, it would be regarded as a motor vehicle for the purpose of the vehicle importation laws, and would have to be declared as such. If the vehicle was not originally manufactured to comply with all applicable FMVSS, it could not be lawfully imported unless it is determined eligible for importation by NHTSA and is imported by an RI or by a person who has a contract with an RI to modify the vehicle so that it conforms to all applicable standards following importation.


If a vehicle is shipped without its engine and drive train, it would be treated, for importation purposes, not as a motor vehicle but instead as an assemblage of motor vehicle equipment items. In this instance, the vehicle would be entered under Box 1 on the HS-7 Declaration form, which covers motor vehicle equipment not covered by a standard, or manufactured before the date that an applicable standard takes effect. Any items included in the assemblage that are subject to an FMVSS (brake hoses, brake fluid, glazing, lighting equipment, seat belt assemblies, tires, rims) that were not manufactured to comply with the applicable standard, and/or were not so certified by their original manufacturer, must be removed from the assemblage and exported or destroyed before entry. Any covered equipment items that were manufactured in compliance with the applicable FMVSS, and were so certified, must be entered under Box 2A.


10. Importing a disassembled vehicle.


A disassembled vehicle that is shipped without an engine and transmission is treated for importation purposes not as a motor vehicle, but instead as an assemblage of motor vehicle equipment items. Such an assemblage can lawfully be imported into the U.S., provided any equipment included in the assemblage that is subject to FMVSS, but was not originally manufactured to comply with that FMVSS or was not so certified by its original manufacturer, is removed from the assemblage prior to entry into the U.S. Equipment items that are subject to the FMVSS include tires, rims, brake hoses, brake fluid, seat belt assemblies, glazing materials, and lamps, reflective devices, and associated equipment.


If the assemblage is shipped with an engine and power train (even if those components are not installed), it would be regarded for importation purposes as a motor vehicle, and would have to be either manufactured to comply with all applicable FMVSS, and be so certified by its original manufacturer, in the form of a label permanently affixed to the vehicle, or be determined eligible for importation by NHTSA and be imported by an RI or by a person who has a contract with an RI to bring the vehicle into compliance with all applicable FMVSS after importation.


11. Importing a right-hand drive vehicle.


In order to be lawfully manufactured or imported for sale in the U.S., a motor vehicle must comply with all applicable FMVSS issued by NHTSA. It is possible for a right-hand drive (RHD) vehicle to be manufactured in compliance with the FMVSS.


A motor vehicle that was not originally manufactured to comply with all applicable FMVSS, and/or was not so certified by its original manufacturer, in the form of a label permanently affixed to the vehicle, cannot be lawfully imported into the U.S. unless it is determined eligible for importation by NHTSA. The agency makes these decisions on the basis of a petition from an RI. These are business entities that are specifically approved by NHTSA to import nonconforming vehicles and to perform the necessary modifications on those vehicles so that they conform to all applicable FMVSS. The petitions must specify that the vehicle is substantially similar to a vehicle that was certified by its original manufacturer as conforming to all applicable FMVSS and is capable of being readily altered to conform to those standards, or, if there is no substantially similar U.S.-certified vehicle, that the vehicle has safety features that comply with, or are capable of being altered to comply with, the FMVSS based on destructive test information or other evidence the agency deems adequate.


As previously indicated, an import eligibility decision can be based on the substantial similarity of a non-U.S. certified vehicle to a vehicle manufactured for importation and sale in the United States, and so certified by its original manufacturer. If the vehicle you are seeking to import is a RHD, even if there were a U.S.-certified left-hand version of that vehicle, it might not be considered "substantially similar" for import eligibility purposes. Our experience has shown that the safety performance of RHD vehicles is not necessarily the same as that of apparently similar left-hand drive vehicles offered for sale in this country. However, NHTSA will consider the vehicles "substantially similar" if the manufacturer advises the agency in writing, on the manufacturer’s letterhead (and not that of an authorized dealership or other such entity affiliated with the manufacturer) that the RHD vehicle would perform the same as the U.S.-certified left-hand drive vehicle in crash tests. Absent such evidence, the petitioning RI would have to demonstrate that the vehicle, when modified, would comply. In this case, you might want to contact one or more of the RIs listed on our website to obtain their opinion on the feasibility of conforming the RHD vehicle to the FMVSS, and the costs involved in conforming the vehicle and petitioning NHTSA for a determination as to whether the vehicle is eligible for importation.


12. Importing a vehicle for show or display.


Certain motor vehicles that are deemed to be of unusual historical or technological significance can be imported for purposes of show or display. Information on importing a motor vehicle for those purposes can be found on NHTSA’s website at http://www.nhtsa.dot.gov/cars/rules/import/ShowDisplay/. When a vehicle is imported for purposes of show or display, it cannot be driven in excess of 2,500 miles per year. As a general rule, a motor vehicle will not be determined eligible for importation for purposes of show or display if more than five hundred vehicles of the same model were produced, if a version of the vehicle was originally manufactured for sale in the U.S. and certified as complying with all applicable FMVSS, or if the vehicle has been determined eligible for importation based on its capability of being modified to comply with all applicable FMVSS.


13. Importation of an off-road vehicle.


If the vehicle was not primarily manufactured for use on public streets, roads, and highways, it would not qualify as a "motor vehicle" that must comply with all applicable FMVSS, and bear a label certifying such compliance that is permanently affixed by its original manufacturer to be lawfully imported into the U.S. A vehicle that is not primarily manufactured for on-road use can be imported under Box 8 on the HS-7 Declaration form that is to be given to Customs at the time of entry. Such a vehicle is not subject to NHTSA’s jurisdiction, but may be subject to the jurisdiction of the Consumer Products Safety Commission (CPSC). For information on the requirements, if any, that apply to these vehicles, you should visit the CPSC’s website at http://www.cpsc.gov or contact that agency at 1-800-638-2772.


14. Importing a racing vehicle.


If the vehicle was originally manufactured as a racing vehicle, it can be permanently imported into the U.S. under Box 8 on the HS-7 Declaration form that is to be given to Customs at the time of entry. The importer must obtain a letter from the vehicle's original manufacturer confirming that it was originally manufactured as a racing vehicle. A copy of the manufacturer's letter should be attached to the HS-7 Declaration form that is submitted to Customs when entry in made. In this instance, no approval from NHTSA is necessary to import the vehicle.


If the vehicle was not originally manufactured as a racing vehicle, it can only be imported on a temporary basis under Box 7 on the HS-7 Declaration form. A NHTSA permission letter is necessary to import a vehicle on this basis. NHTSA grants permission in annual increments for up to 3 years if duty is not paid on the vehicle, or for up to 5 years if duty is paid. If the vehicle was originally manufactured for on-road use, it would have to be in full race configuration at the time of importation, and lack equipment and features needed for on-road use.


Information on importing vehicles for racing purposes is available on NHTSA's website at http://www.nhtsa.dot.gov/cars/rules/import/racing.


15. Temporary importation by non-U.S. residents.


Nonresidents of the U.S. (including U.S. citizens living abroad) may temporarily import nonconforming motor vehicles into the U.S. for personal use, for a period not to exceed one year. The vehicle must be registered in a country other than the U.S. at the time of entry, must not be sold while it is in the U.S., and must be exported when the year is up. If you wish to import your vehicle under these conditions, you should check Box 5 on the HS-7 Declaration Form to be given to Customs at the time of entry. Your passport number and the country that issued the passport must be specified on the declaration. An international convention governs the importation of these vehicles. The U.S. is a signatory to this convention. The convention provides that vehicles can be imported under its terms for a period of up to one year. NHTSA has no authority to extend the one-year period that a vehicle imported in this manner is allowed to remain in the U.S.


16. Temporary importation of a vehicle; expiration of temporary importation period.


Motor vehicles that were not originally manufactured to conform to all applicable FMVSS may be temporarily imported into the U.S. for specified purposes, including research, investigations, demonstrations or training, or competitive racing events. Vehicles imported for those purposes are entered under Box 7 on the HS-7 Declaration form to be given to Customs at the time of importation. Unless the importer is a manufacturer of motor vehicles that are certified to the FMVSS, a NHTSA permission letter is needed to accomplish such an importation. Instructions and an application for obtaining a NHTSA permission letter are found on our website at http://www.nhtsa.dot.gov/cars/rules/import. Once the application is completed, it should be faxed to the Office of Vehicle Safety Compliance, Import and Certification Division at 202-366-1024. We grant approval for temporary importations under Box 7 in annual increments for up to three years if duty is not paid on the vehicle, or for up to five years if duty is paid. We are not averse to granting extensions to existing approvals if we receive a request in writing to do so, supported by a full explanation of why the extension is needed. Vehicles that are temporarily imported must be exported or destroyed upon the expiration of the period for which importation has been allowed.


17. Exporting a vehicle.


NHTSA does not regulate the exportation of vehicles from the U.S. We only regulate the importation of vehicles into this country. Therefore, we can offer no guidance on this subject. If you have a question regarding the exportation of a vehicle, you may want to direct that question to the Customs Director at the port through which you intend to ship the vehicle or visit http://www.customs.gov.


Additional Information on the NHTSA Website

Importing a Canadian-certified motor vehicle

For detailed information on how to import a Canadian-certified vehicle please visit our website at http://www.nhtsa.dot.gov/cars/rules/import.


Importing a non-U.S. or Canadian –certified (Gray Market) Motor Vehicle

For detailed information on importing a non-U.S. or Canadian-certified motor vehicle, such as one that was originally manufactured for sale in Europe or in the Far East, please visit out website at http://www.nhtsa.dot.gov/cars/rules/import.


How to Become a Registered Importer

For detailed information on how to become a Registered Importer please visit our website at http://www.nhtsa.dot.gov/cars/rules/import.


List of FMVSS

For a booklet that lists the FMVSS, and provides a brief description of each standard, please visit our website at http://www.nhtsa.dot.gov/cars/rules/import.


List of Registered Importers

For a listing of all Registered Importers in active status with NHTSA, please visit our website at http://www.nhtsa.dot.gov/cars/rules/import.


HS-7 Declaration Form

To download a copy of the HS-7 Declaration form, please visit our website at http://www.nhtsa.dot.gov/cars/rules/import.


Vehicles Eligible for Importation-Eligibility List

Vehicles on this list may ONLY be imported under bond and by an RI. For a list of vehicles that NHTSA has determined to be eligible for importation, please visit our website at http://www.nhtsa.dot.gov/cars/rules/import.


Examples of Imported Vehicles into the United States
Importing a Nissan Skyline.

Importing a Mercedes Smart Car.


I. Importing a Nissan Skyline.


The Nissan Skyline was not originally manufactured to comply with all applicable FMVSS. Such a vehicle that is less than 25 years old can only be lawfully imported into the U.S. if (1) it is determined eligible for importation by NHTSA and (2) it is imported by an RI or by a person who has a contract with an RI to bring the vehicle into compliance with all applicable FMVSS within 120 days of entry.

Import eligibility decisions are made on a make, model, and model year basis. NHTSA has determined that the 1990-1999 versions of the RHD Nissan GTS and GTR (“Skyline”) are eligible for importation and has assigned vehicle eligibility number VCP-17 to those vehicles. (The import eligibility number is to be entered on the HS-7 Declaration form that is to be given to Customs at the time of entry, and alerts Customs that the vehicle may be lawfully imported by an RI or by a person who has a contract with an RI, even though the vehicle is not certified by its manufacturer as complying with all applicable FMVSS.)

To learn the modifications the petitioner stated were needed to conform to the 1990-1999 Skyline to the FMVSS, you should go to the DOT Docket website at http://dms.dot.gov and enter docket number 5507 in the appropriate block on the simple search screen. A list of RIs can be found on our website at http://www.nhtsa.dot.gov/cars/rules/import. You should consult the importers on that list to see whether any are willing to conform the vehicle that you seek to import to all applicable safety and bumper standards, and if so, what they would charge for that work.

If you decide to import the vehicle, one potential complicating factor is that the RI who petitioned NHTSA to determine the 1990-1999 model Skyline eligible for importation requested, and was granted, confidentiality with respect to the modifications needed to conform to the vehicle to certain of the standards. As a consequence, that importer (Motorex of Gardena, CA) has claimed a proprietary interest in the modifications covered by the confidentiality grant. This does not preclude other RIs from attempting to modify the vehicle. However, should those importers not gain access to the modifications covered by the grant confidentiality, they will have to demonstrate to the agency, at the time they submit a conformity certification package for a Skyline, that they have made equivalent modifications that permit the vehicle to comply with the standards covered by the confidentiality grant.

Please note that we determined the vehicle eligible for importation based on its capability of being modified to comply with all applicable standards. We did not approve Motorex, or any other RI as the “exclusive” importer of the vehicle. As previously indicated, another RI is free to import the vehicle, but will have to demonstrate in the conformity package submitted to the agency to obtain release of the conformance bond furnished at the time of importation that the vehicle has been brought into conformity with all applicable standards, including those covered by the grant of confidentiality to Motorex.

You should note that if you were to import the vehicle, the necessary modifications would have to be made by an RI, and that importer would have to certify to us that the vehicle conforms to all applicable FMVSS in effect on its date of manufacture before the vehicle could be released to be licensed or registered for on-road use. One of the reasons that an RI is required to import and modify a vehicle that was not originally manufactured to comply with all applicable FMVSS is because the RI stands in the stead of the vehicle’s original manufacturer to provide the vehicle’s owner with notification and remedy in the event that the vehicle is determined to contain a safety-related defect or a noncompliance with an applicable safety standard. Because the original manufacturer would not be responsible for the vehicle being in the U.S., it would have no legal obligation to perform this import safety responsibility.

Questions regarding modifications to conform the vehicle to applicable emissions standards should be directed to the EPA.

II. Importing a Mercedes Smart Car.

A vehicle that was not originally manufactured to conform to all applicable FMVSS cannot be lawfully imported into the U.S. unless it is first determined by NHTSA to be eligible for importation. The agency makes these decisions on the basis of petitions from RIs. These are business entities that are specifically approved by NHTSA to import nonconforming vehicles and to perform the necessary modifications on those vehicles so that they conform to all applicable FMVSS. The petitions must specify that the vehicle is substantially similar to a U.S.-certified vehicle, or that the vehicle has safety features that comply with, or are capable of being altered to comply with, the FMVSS based on destructive test information or other evidence the agency deems adequate.

Import eligibility decisions are made on a make, model, and model year basis. On January 22, 2004, we granted import eligibility to the 2003-2004 glass top and convertible versions of the Passion model Smart Car, and to the 2002-2004 Passion, Pulse, and Pure model Smart Cars. As a result of our decision, any of the model and model year vehicles identified above can be imported by an RI or by a person who has a contract with an RI to bring the vehicle into conformity with all applicable FMVSS. A list of RIs that are currently in active status can be found on our website at http://www.nhtsa.dot.gov/cars/rules/import. You might wish to contact one or more of the RIs on that list to learn the cost of modifying one of these vehicles so that it conforms to all applicable FMVSS.

We have made a blanket import eligibility decision that covers all Canadian-certified passenger cars manufactured on or after September 1, 2002, that, as originally manufactured, are equipped with an automatic restraint system that complies with our occupant crash protection standard and that also were originally manufactured to comply with other specified standards. Owing to these limitations, Canadian – certified smart cars could only be lawfully imported if they were determined eligible for importation on a separate make, model, and model year basis.

Questions regarding modifications to conform the vehicle to applicable emissions standards should be directed to the EPA.

Here is the Vehicle Eligibility List, it's to big for this post.
http://www.nhtsa.dot.gov/cars/rules/import/ELIG071404.html

[popstar]

soooo !

who gonna import a GT-4 as a show car then and disconnect the speedo for most of the year to stay under the 2500 miles per year thing !!!!

looks like your best shot

some good info DS, i hope someone will make good use of it

[playr158]

just drive the GT4 and use your USDM gauges in it
and never drive the usdm

[rlan214]

just drive the GT4 and use your USDM gauges in it
and never drive the usdm
[right][snapback]312634[/snapback][/right]

actually this is what I was thinking of doing
I calculated I have to at least 12k just to bring the car over here

[playr158]

thats not bad considering what you could run with...

evos, s2k, sti....ect...
12k is worth it

[darksecret]

Especially seeing how much it cost buying from an RI, PSI in Charlotte was asking $34,000 for a '94 R32 Skyline with a stock RB20 and an auto, it also had around 120,000 miles which isn't bad but it doesn't matter if it was 5 miles for that price. Shipping isn't all that bad either, it's around $3,000-$4,000 USD to bring a car from Australia, well that is what my secretary tells me and she's from Port Lincoln near Adelaide and i've found '99 RS200 Altezza's for a little over $14,000USD.
BTW be prepared to wait about 6 months for the inspections and other BS, or just get a car on the VEL that doesn't need permission from the manufacturer to be shipped like the Skyline.

This post has been edited by darksecret: Jul 15, 2005 - 10:18 AM

[Clipsetuner]

Really good information. I am try'n to currently get a GT4 and 12k seems a little high I got quoated on 2 different cars between 8k-9k shipped to Vancouver, BC.

I wont be taking all those steps to make mine "legal" persay but it will be legal on the street. I hope once I get the whole thing orginized and its on a boat ill be alot happier about it but we'll see how long this whole process takes.

Basicly what I am gonna pull off which I know people who have is do a "RHD conversion" which is legal as long as you meet the regulations and have pictures of the entire process. It just so happens right now that my buddy has a stripped Cozmo that will pull off the RHD part, and now I am on the hunt for a wrecked 6th gen.

I have dreams of swaping a FWD celica but then did some research and found I can get a nice GT4 for just a bit more.

DTE

[darksecret]

True, but if it's imported it still needs that little sticker in the windshield to be legal, even if it's a modified american vehicle it will have to repass an emissions and safety inspection.

[Mr_E]

15. Temporary importation by non-U.S. residents.