Test fit my 2-post., Pics inside. Options

[celiracer]

Hey guys just test fitted my wing today. I have pics
and wanna know what everyone thinks.

Does this gap close when you screw them screws from the block to the wing?
Didn't want to do everything till its painted.


Then i have these three holes that i need to shave.




And here are three pics of what it looked like on my car. Let me know what
you guys think.





I also have a C-one replica Front, 404 sides, and 404 rear
that are getting put on with my car getting re-painted.

[fastcelica20]

looks hot man! but lower your car a bit. good job!

[Valo666]

nice..you get the blocks from romas?? i wanted 2 order a set, but i was 2 late you keepin the car red? or you gonna re-paint it?

[celiracer]

Yea its getting lowered 1 1/2 inches. with the kit. I am keeping it the same red.

[DSRT-FX]

can't wait to see them on mate, are you going to spray the raiser blocks black on match them red? im going for the same look aswell although having to drill more holes and reshave the existing 3-post wing holes seems to be abit much for me only time and money will tell hehe.. good luck... just a question does the 2-post wing cover the existing 3-post wing holes at all? i know the pics show they don't but is it very obvious? -R

[celiracer]

I'm painting everything red. And with the 3-post spoiler stock you have to shave the middle and the one hole and each side also have to drill an extra hole on each side for the other bolt.

Did anyone else have a gap in the inside part, where the block and spoiler connect?

This post has been edited by celiracer: Apr 23, 2006 - 7:56 PM

[ThAixGuYx2k7]

DO IT!

[celiracer]

My biggest question is. Since i have the gaps on each side like on the first pic how would i go about fixing that and making it flush??

[bloodrain]

My biggest question is. Since i have the gaps on each side like on the first pic how would i go about fixing that and making it flush??

lots and lots of bondo and sanding, thats what i did. BTW i like ur rotors and calipers

[celicarus]

are those 18's or 19's -- ?

[celiracer]

They are 18's And bloodrain yours was like that also? thats the gay thing im no good at bondo lol. But i guess i gotta learn lol.

[lagos]

did you drill a new hole on each side?


for my car, i didnt shave any of the holes. i just usde black caps to cover them up. it came out looking good. the only hard part was cleaning off that glue that used to be on there.

[celiracer]

Well first off my cars getting re-painted so im shaving the holes that are needed to be shaved plus the sprayer nozzle, and antenna.

I didn't drill the second hole yet. I just put the bold on the back side and put the spoiler on top of it. Just to see how it looked and everything. going to drill the hole and stuff right before it goes into the shop.

[lagos]

oh ok ..sounds good.

its really not too hard going from a 3post to a 2. just a little more work to get it done.

[celiracer]

Thanks for the info Lagos. but did you have that gap problem like my 1st pic? and where would i put the bondo? on the block to try and get it to go farther to the wing? or just put the screws in to hope it closes?

[CelicaZR]

I would like to know how it turns out Celiracer
Cause I plan to buy the same spoiler.

[celiracer]

ok. I'm waiting on my kit. and once that gets here it will be fitted and the wing will get done also. Thanks everyone for their comments and i hope i can get this together and don't have to worry about that gap once the bolts and screws are all on it.

[lagos]

there shouldnt be any gaps. did u cut off the little part that sticks out on the oem spoiler? you have to cut that off for it to sit flush with the blocks. then use some doubble sided tape, and some screws to hold it all in place

[celiracer]

Lagos do you have any pics of what you have to cut off on the spoiler? I didn't know you had to cut anything off.

[celiracer]

Lagos if you can could you show me a pic of what you cut off the spoiler?