6G Celicas Forums

Welcome Guest ( Log In | Register )

 
Reply to this topicStart new topic
> Fitting Question
post Dec 8, 2004 - 7:09 PM
+Quote Post
initialdrift55



Enthusiast
***
Joined Sep 23, '03
From Miami,FL
Currently Offline

Reputation: 0 (0%)




hey guys havent posted in a bit because i have been saving money and finally its time to give the lady a present...Question: If i get the stock gt4 front bumper w/o the hood meaning i will be putting the front bumper with my stock hood will there be a gap? or the gap only shows if its the gt4 hood with stock front?

thanx
post Dec 8, 2004 - 10:50 PM
+Quote Post
initialdrift55



Enthusiast
***
Joined Sep 23, '03
From Miami,FL
Currently Offline

Reputation: 0 (0%)




:bump:
post Dec 8, 2004 - 11:09 PM
+Quote Post
celicaspeed

Enthusiast
**
Joined Aug 22, '04
From kitchener,Ontario
Currently Offline

Reputation: 0 (0%)




I think that there will be a bump.
post Dec 9, 2004 - 1:15 AM
+Quote Post
playr158



Enthusiast
*****
Joined May 22, '03
From NOVA
Currently Offline

Reputation: 16 (100%)




well with a gt-4 front bumper and stock hood you'll have a gap but facing the windshield meaning if your in the car you can see into the bumper
post Dec 9, 2004 - 2:58 PM
+Quote Post
initialdrift55



Enthusiast
***
Joined Sep 23, '03
From Miami,FL
Currently Offline

Reputation: 0 (0%)




as figured thank you
post Dec 9, 2004 - 3:02 PM
+Quote Post
initialdrift55



Enthusiast
***
Joined Sep 23, '03
From Miami,FL
Currently Offline

Reputation: 0 (0%)




one more question...is ALL the stuff on this list Needed to fit the Front bumper?

GT-Four Hood and Bumper - This is the hood and front bumper combination that can be found on all sixth generation Celica GT-4s. It's highly recommended that you buy both at the same time, because if you only buy one without the other, there will be a ugly, noticable gap in the center of the car where the hood meets the front bumper. The part numbers for everything necessary are below.
Bumper Parts
Cover, front bumper 52521-20200 $223.27 This is the bumper
Absorber, front bumper energy 52611-20150 $62.76 This is the foam that goes behind the bumper
Seal, hood to front end panel 53395-20020 $19.92 This is the rubber seal where the hood and bumper meet
retainer, front bumper upper center 52521-20200 $25.44 this is the metal thing that holds the rubber in place
Grill, sub-assy, rad., center 53101-20500 $46.29 This is the upper grille
Grill, radiator, lower 53111-20750 $125.08 This is the lower grille
Bezel, grille, lower RH 53112-20240 This is the right-hand bezel for the lower grill without fogs
Bezel, grille lower LH 53113-20180 This is the left-hand bezel for lower grill without fogs
Front turn signal, RH 81510-20750
Front turn signal, LH 81520-20750
Fog Lights and other Optional Parts
Fog lamp, RH 81210-20370
Fog lamp, LH 81220-20360
Bezel, grill lower RH 53112-20230 This is the right-hand fog light bezel
Bezel, grill lower LH 53113-20180 This is the left-hand fog light bezel
Latch, hood, LHD 53510-20510 This is the left-hand-drive GT-Four hood latch, without it, you'll have to lengthen your stock latch by about 1/2 inch.
Bracket, upper grill #1 53115-20070 $13.95 This is 1 of 2 brackets which hold in the upper grill
Bracket, upper grill #2 53118-20070 $15.46 This is the 2nd bracket for the upper grill
You can also get the reinforcment bar(your "crash-bar" or 5MPH bumper) and frame brackets, but theyre not nessicary, and the frame brackets required to use them are $180 EA from toyota. so just about everyone dont get it, they just cut down theyre crash bar with a sawzall.
post Dec 9, 2004 - 7:34 PM
+Quote Post
Drocay



Enthusiast
*****
Joined Oct 3, '02
From Va Team 6gc
Currently Offline

Reputation: 1 (100%)




yup that looks about right.


--------------------
IPB Image
All I have in this world is my Balls and my Word and I'm not breaking em for no one,- Tony Montana
Team 6gc 2005
post Sep 16, 2006 - 4:41 PM
+Quote Post
Alan



Enthusiast
**
Joined Jan 23, '05
From Malta
Currently Offline

Reputation: 2 (100%)




QUOTE(initialdrift55 @ Dec 9, 2004 - 3:02 PM) [snapback]219241[/snapback]

one more question...is ALL the stuff on this list Needed to fit the Front bumper?

GT-Four Hood and Bumper - This is the hood and front bumper combination that can be found on all sixth generation Celica GT-4s. It's highly recommended that you buy both at the same time, because if you only buy one without the other, there will be a ugly, noticable gap in the center of the car where the hood meets the front bumper. The part numbers for everything necessary are below.
Bumper Parts
Cover, front bumper 52521-20200 $223.27 This is the bumper
Absorber, front bumper energy 52611-20150 $62.76 This is the foam that goes behind the bumper
Seal, hood to front end panel 53395-20020 $19.92 This is the rubber seal where the hood and bumper meet
retainer, front bumper upper center 52521-20200 $25.44 this is the metal thing that holds the rubber in place
Grill, sub-assy, rad., center 53101-20500 $46.29 This is the upper grille
Grill, radiator, lower 53111-20750 $125.08 This is the lower grille
Bezel, grille, lower RH 53112-20240 This is the right-hand bezel for the lower grill without fogs
Bezel, grille lower LH 53113-20180 This is the left-hand bezel for lower grill without fogs
Front turn signal, RH 81510-20750
Front turn signal, LH 81520-20750
Fog Lights and other Optional Parts
Fog lamp, RH 81210-20370
Fog lamp, LH 81220-20360
Bezel, grill lower RH 53112-20230 This is the right-hand fog light bezel
Bezel, grill lower LH 53113-20180 This is the left-hand fog light bezel
Latch, hood, LHD 53510-20510 This is the left-hand-drive GT-Four hood latch, without it, you'll have to lengthen your stock latch by about 1/2 inch.
Bracket, upper grill #1 53115-20070 $13.95 This is 1 of 2 brackets which hold in the upper grill
Bracket, upper grill #2 53118-20070 $15.46 This is the 2nd bracket for the upper grill
You can also get the reinforcment bar(your "crash-bar" or 5MPH bumper) and frame brackets, but theyre not nessicary, and the frame brackets required to use them are $180 EA from toyota. so just about everyone dont get it, they just cut down theyre crash bar with a sawzall.


by any chance do you have the part number of the Reinforcment brackets plz smile.gif


--------------------
IPB Image

Reply to this topicStart new topic
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:

 



Lo-Fi Version Time is now: November 27th, 2024 - 11:12 AM