fs: PICS ADDED 1995 celica with 3sgte swap, 4500$ Options

[brianforster]

drivers side:

front:

pass side:

back:

close up of drivers side fender dent:

another front:

hood clear coat bubble:

passenger side dent behind door:

spoiler clear coat:

interior:

interoir:

engine bay:


2nd Gen JDM 3sgte

Precision Turbo FMIC
Upgraded CT26
(T04E 46 trim and 10* clip)
2.5" Aluminum Intercooler Piping
full 3" exhaust
3" (reinforced) SS Autocrap Downpipe
3" High-Flow Cat
3" Magnaflow Mufflef
Unorthodox Racing Underdrive Pulley
Centerforce stage 3 dual friction clutch

new plugs/plug wires/cap/rotor/coil

16xk miles on chassis, not sure on motor as i bought from someone on the site who bought from someone else on the site.

rear brake conversion is done new rotors/pads in back

comes with 17" scion Tc wheels with 225/45/17 khumo ecsta asx's on the back less than 500 miles on them, wheels probably need to be balanced, the place that put them on must have did it wrong because theres a slight pulsating vibration at highway speeds.

the bad:
the shell needs a paint job, right now theres a dent in the passenger side behind the door and a dent in the drivers side fender real low, the doors are also touch up painted red so its not as shiney as the rest of the car but it doesnt look bad, theres also clear coat bubling in places.

inside is pretty good, comes with a 2 gauge pillar gauge pod, and a boost gauge and a greddy profec spec b boost controller but im not sure if it works or if i hooked it up wrong but its kind of finnicky. it also has an HKS knock off BOV hooked up now that works fine.

the car has power steering but no a/c the compressor is hooked up but the lines are not, i have the lines at home the only thing youd have to buy is a condensor.

problems with engine:
nothing major, just a leak from the HFHOE caused by the clamp either wearing out and sliding down or just not being put back on correctly, im in the process of fixing it and probably can fix it by the time the car would be sold unless this goes realy quickly or something.

the exhaust manifold is leaking because the right most stud wont tighten down, its a small leak and just makes a little tapping noise when revving, i have an idea on how to fix this too but i havent gotten around to it, just letting everyone know each problem.

THE COOLANT LEAK AND EXHAUST LEAK HAVE BEEN FIXED AS OF 11/1/06 I AM LEAVING IT IN THE POST HOWEVER TO SHOW YOU HOW UPFRONT I AM ABOUT THIS CAR!

the tranny shifts fine but sometimes can be notchy, third gear clunks if you try to shift fast and hard, this would probably be fixed by switching to a good gear oil like redline. i think the shifting can be notchy at times due to the clutch needing a bleed, yet another thing i havent gotten around to.

i also think that the rear struts may be going bad as the ride is a little stiff, i was waiting to replace them because i was gonna buy some teins.

i have put a lot of time and money into this car but now that i am going to be living at college year round and i have no space to work on a car the car just sits, id like to buy a econobox daily driver and get a job and get my life on track. id say that this car would be perfect for a project car because its ready for your molding, there are no exterior modifications and its got a 3sgte swap, if the car gets a paintjob and the few small repairs are made on the engine the car would be worth way more, but im pricing this thing to sell and im also pricing it to what i think id pay for the car.

im located in towson, md.

edit: the car is red and i will try to get pics up asap, if any of you have any questions feel free to post here i will answer anything you need to know about this car because i pretty much know every bolt on it.

price is 4500 as said in title, i feel this is fair considering there are a lot of good aspects of the car and it could be daily driven, it passed maryland state inspection like 3 months ago and i havent really driven it much since then.

This post has been edited by brianforster: Nov 1, 2006 - 8:14 PM

[block]

NOOOOO. why are everyone selling their cars?!?!?!?

[JFrost9]

It seems like all these problems are small enough for you to fix before selling it, I am interested, but dont wanna buy a car from a guy who isnt even willing to work out the small problems, Id hoped you would have taken care of this thing. I know you put a lot of hard work into it, and i will be following this as you update it with the problems fixed.

[brianforster]

one of the main reasons for me selling this is that im getting tired of having a car to tinker with i just want a car i can drive every day, im not saying this has been unreliable but its no grocery getter.

i am 100% upfront with the problems i posted and will offer any more information i may have up, i will attempt to fix the problems it does have this week though and get back to you.

i do however feel comfortable in saying that there are no undiagnosed problems on this car, each tiny little imperfection and flaw is accounted for.

[Toyoca]

wanna put your engine in my car? =)

[94celicadude]

wanna put your engine in my car? =)

haha +1

[brianforster]

wanna put your engine in my car? =)

itd probably be cheaper to buy my car

[j0e_p3t]

pics? and 245/45/17 tires?

[brianforster]

pics? and 245/45/17 tires?

good call i meant 225/45/17

[bojangles_8686]

BRIAN NOOOOOOOOO!!!!!!!!

sh*ts weak brian, sh*ts weak

This is a good deal for whoever buys this car. He has put a lot of time and money into it. I know this because I was there with him for a majority of it. Good luck with the sale Brian.

This post has been edited by bojangles_8686: Oct 31, 2006 - 8:49 AM

[Fate]

i'm interested i just need to talk it over with my parents, when are you on AIM cuz' whenever i try to get ahold of you you're away i guess?

[Fastbird]

Not to be a buzzkill, but the exhaust manifold bolt that won't tighten, that's most likely at the very least going to necessitate the removal of the manifold/turbo/downpipe to get a tap in the bolt hole. Depending on the condition of the threads, you may or may not be able to repair with a simple tap. If not, it's going to need to be drilled and have a helicoil installed, which I'm not sure if there's room in the engine bay to do that so the head may have to come off too.

Of all the problems you've listed, that's the worst. The rest seems to be just minor stuff. This car sounds like an outstanding opportunity to jump into the GTE world for a great price.

[brianforster]

you dont have to remove the turbo to remove the manifold, but well leave that to another thread.
edit: if it did come down to helicoiling it the head would not need to be removed...

your advice is well received fastbird but if you are going to add something like that to the thread then atleast be accurate, i replaced the manifold without taking off the turbo or downpipe and not a single stud hole would require the removal of the head to retap/helicoil.

This post has been edited by brianforster: Oct 31, 2006 - 11:38 AM

[RbrtNdrws]

pics?

[jgreening]

Good luck with the sale Brian. I have some thoughts for you. If you want to hear them, hit me up on PM.

[bigal004321]

dammit i wish i would have known this in may before i bought my 3sgte shucks..anyway good luck with the sale!

Bigal

[Fastbird]

you dont have to remove the turbo to remove the manifold, but well leave that to another thread.
edit: if it did come down to helicoiling it the head would not need to be removed...

your advice is well received fastbird but if you are going to add something like that to the thread then atleast be accurate, i replaced the manifold without taking off the turbo or downpipe and not a single stud hole would require the removal of the head to retap/helicoil.

That's why I said I wasn't sure if the head had to come off. I just never bothered to see if there was room in there to get a drill to get things done. My bad.

[brianforster]

both the coolant leak and the exhaust leak are fixed like i said, easy fixes, just took time, i need to find somewhere to host my pictures, i took a bunch, so the thread will be updated shortly with pics.

[Chanh55]

Pic of the car. Sorry to hear you selling man took you a long time to find the shell and put a lot of work into getting that engine in...



This post has been edited by Chanh55: Nov 1, 2006 - 5:43 PM

[hitcachi]

dude, you have put so much work and time into this car. why!!