6G Celicas Forums

Welcome Guest ( Log In | Register )

 
Reply to this topicStart new topic
> Powerwashing engine, how to do it safely
post Mar 27, 2009 - 12:38 PM
+Quote Post
nightryder

Enthusiast
**
Joined Sep 29, '05
From Rochester, Massachusetts
Currently Offline

Reputation: 2 (100%)




Ive been told to powerwash my engine in order to clean it up so i can locate an oil leak.



so does anyone know the proper procedures to do so? Just to make sure i dont damage anything electrical



i would have to assume you have to keep something dry...


--------------------
IPB Image
The question is not how far. The question is, do you possess the constitution, the depth of faith, to go as far as is needed?
post Mar 27, 2009 - 12:41 PM
+Quote Post
Ryouxrs



Enthusiast
**
Joined Mar 26, '09
From Longmont, CO.
Currently Offline

Reputation: 0 (0%)




the biggest things u have to worry about is getting water in your intake, and distributor, so ducktape a plastic baggie aroung your distributor and the intake filter if u have an sri. other than that have at it! lol

This post has been edited by Ryouxrs: Mar 27, 2009 - 12:41 PM


--------------------
Lift Addict!! ^_^
----------------------
post Mar 27, 2009 - 12:43 PM
+Quote Post
nightryder

Enthusiast
**
Joined Sep 29, '05
From Rochester, Massachusetts
Currently Offline

Reputation: 2 (100%)




i had heard that i need too keep the engine running so i dont get water on the sparks




and what about the alternator? i feel like that is very exposed


--------------------
IPB Image
The question is not how far. The question is, do you possess the constitution, the depth of faith, to go as far as is needed?
post Mar 27, 2009 - 1:16 PM
+Quote Post
BonzaiCelica



Enthusiast
*****
Joined Apr 24, '08
From Orange County, CA
Currently Online

Reputation: 33 (100%)




QUOTE (nightryder @ Mar 27, 2009 - 1:38 PM) *
Ive been told to powerwash my engine in order to clean it up so i can locate an oil leak.


well just use brake parts cleaner to locate where your leak is. but at the same time its a good idea to wash engine if you'd like.

when i did it. i dont remember duct taping/covering the alternantor. i covered up electrical parts that were under the hood like injectors and eletrical wires that were near injectors, duct taped throttle body. also use engine decreaser and shine.


--------------------
Group buy to replicate Narrow E series transaxle parts

http://www.6gc.net/forums/index.php?showto...p;#entry1107514
post Mar 27, 2009 - 1:38 PM
+Quote Post
Ryouxrs



Enthusiast
**
Joined Mar 26, '09
From Longmont, CO.
Currently Offline

Reputation: 0 (0%)




u dnt have to worry about the alternator, it will be fine. DO NOT have the engine running when u wash it. u will almost for sure short something out or damage electrical components if you do, just cover those 2 things realy good, and u shouldnt have any problems.


--------------------
Lift Addict!! ^_^
----------------------
post Mar 27, 2009 - 2:38 PM
+Quote Post
jordisonjr



Enthusiast
*****
Joined Jan 20, '09
From Winnipeg
Currently Offline

Reputation: 5 (100%)




Once washed is it safe to drive? Or should you wait till its all dry?


--------------------
-Protection mode, For when your amp tries to blow its load.

1995 Toyota Celica GTS - Daily Driver
1999 Chevy Cavalier - Winter Beater
1994 Honda Civic CX Hatchback - Dead

My Celica!
post Mar 27, 2009 - 3:24 PM
+Quote Post
Ryouxrs



Enthusiast
**
Joined Mar 26, '09
From Longmont, CO.
Currently Offline

Reputation: 0 (0%)




u could drive it right away if u seal off those 2 things


--------------------
Lift Addict!! ^_^
----------------------
post Mar 27, 2009 - 4:38 PM
+Quote Post
samir0189



Enthusiast
****
Joined Mar 8, '08
From Orlando, Florida
Currently Offline

Reputation: 14 (100%)




If by power washing you mean using a pressure washer, be careful around all the plastic clips for electrical plugs. the plastic will be very brittle because of years of putting up with the engine heat, alot of mine break off in my hand, so I wouldn't want to imagine what water at 2000psi would do to them.

IMO you'd be better off with a strong degreaser, maybe a sponge to scrub around and just a normal hose.

This post has been edited by samir0189: Mar 27, 2009 - 4:40 PM


--------------------
My F/S Thread!

QUOTE
(14:19:21) Daniel: That was a JDM hole in the side of the box too. There was so much JDM trapped inside that box that they couldn't contain it, so they had to put a JDM hole in the box to let the JDM out.

QUOTE
Ferdi says (11:29)
No, it looks like a hooker put her acid vag on your hood. Acid vag = bigger problem than a few dings.
post Mar 28, 2009 - 1:10 PM
+Quote Post
reko



Enthusiast
**
Joined Apr 17, '07
From Montreal, QC, Canada
Currently Offline

Reputation: 1 (100%)




Blow air with a compressor after you cleaned it so it will dry faster


--------------------



Reply to this topicStart new topic
4 User(s) are reading this topic (4 Guests and 0 Anonymous Users)
0 Members:

 



Lo-Fi Version Time is now: December 4th, 2024 - 11:47 PM